Go Back  HuntingNet.com Forums > Archery Forums > Technical
 Hoyt Cybertech CAM 1/2 tiller adgustment >

Hoyt Cybertech CAM 1/2 tiller adgustment

Technical Find or ask for all the information on setting up, tuning, and shooting your bow. If it's the technical side of archery, you'll find it here.

Hoyt Cybertech CAM 1/2 tiller adgustment

Old 11-02-2003, 10:12 AM
  #1  
Thread Starter
 
Join Date: Nov 2003
Location:
Posts: 18
Default Hoyt Cybertech CAM 1/2 tiller adgustment

I just purchased a CAM & 1/2 Cybertech and when I zero out the weight (crank it all the way up) so I can index(turn the bolt the exact same amount) the weight bolts. The tiller measurement is between a 1/8 to a 1/4 of an inch different,
but if I turn the out the affected limb about a 1/4 of an inch the tiller is right on. ? is it ok for the weight adjust ment bolts to be a little off, not exactly the same amount of turns? Is the top tiller measure ment supposed to be the exact same as the bottom tiller measurement? Or should there be a slight offset Any advice or help would be greatly appretiated.

Thank you
Corey
caz1971 is offline  
Old 11-02-2003, 02:51 PM
  #2  
Fork Horn
 
Join Date: Feb 2003
Location: patten.maine usa
Posts: 147
Default RE: Hoyt Cybertech CAM 1/2 tiller adgustment

Caz,I have the same bow.I would adjust the tiller to be the same and make sure your tune marks are close to the same.How and what are you using to measure your tiller?Mine is on the money cranked down.I shoot it two turns out.Ron
nmaineron is offline  
Old 11-02-2003, 05:21 PM
  #3  
Thread Starter
 
Join Date: Nov 2003
Location:
Posts: 18
Default RE: Hoyt Cybertech CAM 1/2 tiller adgustment

Hay Ron I used a metal ruler and I put it just inside the limb were it reaches the riser limb pocket, I butt it up against the limb and square it from there. I need to check again but I think my bow is either 1/2 or 3/4 of a turn out. I will probably go one full turn. I am going to keep it between 66 and 68 pounds. More cynetic energy. LOL. Thanks for the reply.
caz1971 is offline  
Old 11-03-2003, 09:45 PM
  #4  
Thread Starter
 
Join Date: Nov 2003
Location:
Posts: 18
Default RE: Hoyt Cybertech CAM 1/2 tiller adgustment

Hay Ron & Navy I just didn' t feel right with the fact that turn one limb 1/4 of an inch trun more or less did weigh easy on my mind so I just got finished starting from scratch. I cranked it all the way down on both limbs until they really stopped this time, then I backed them off one whole turn. The tiller is right on, top and bottom limb. I guess I should just double check what the hell I am doing. LOL
caz1971 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Germ
Left Handed Section
0
03-09-2008 10:29 AM
Matchbook454
Archery Gear
2
05-01-2006 05:16 PM
hoytusa10
Whitetail Deer Hunting
1
03-02-2004 12:59 PM
hoytusa10
Bowhunting
1
02-08-2004 05:07 PM
ILL BUCK
Technical
1
02-10-2002 09:01 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Quick Reply: Hoyt Cybertech CAM 1/2 tiller adgustment


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.