cheap easy target holder to pattern your gun
#1

i made this cheap and easy target holder to pattern my gun
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1549.jpg"
very easy to make took me about 15 mins
material needed
1. (2) 10ft 1/2 pvc .98 a piece
2. (2) t connections .20 a piece
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1550.jpg"
3. (2) outside corners 45 .18 a piece
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1551.jpg"
4 (4) toolshop clamps .46 a piece
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1554.jpg"
5 a roll of resin paper 10.97 a roll 36"x500sqft
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1555.jpg"
step 1
cut 2 pieces of pvc at 40" for the top and bottom rail
step2
cut 2 pieces at 42" for the sides
step3
cut 2 pieces at 18" with an angle on 1 end for the stakes
step 4
put the corner pieces on the top rail
step5
put the t's on the bottom rail into the t
step 6
insert the side pieces into the top rail and bottom
step 7
insert the stakes to the bottom of t
step 8 and very important if there is alittle wind out is to insert a screw in all 4 corners by where the claps are so that the clamps will not slide
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1552.jpg"
step 9 cut you some lenths of resin paper at 44" long
NOW YOU ARE READY TO PATTERN YOUR GUNS
GOOD LUCK AND GOOD HUNTING
BY THE WAY ALL MATERIALS WERE BOUGHT AT MENARDS AND THE TOTAL
WAS UNDER 17.00 DOLLARS
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1549.jpg"
very easy to make took me about 15 mins
material needed
1. (2) 10ft 1/2 pvc .98 a piece
2. (2) t connections .20 a piece
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1550.jpg"
3. (2) outside corners 45 .18 a piece
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1551.jpg"
4 (4) toolshop clamps .46 a piece
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1554.jpg"
5 a roll of resin paper 10.97 a roll 36"x500sqft
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1555.jpg"
step 1
cut 2 pieces of pvc at 40" for the top and bottom rail
step2
cut 2 pieces at 42" for the sides
step3
cut 2 pieces at 18" with an angle on 1 end for the stakes
step 4
put the corner pieces on the top rail
step5
put the t's on the bottom rail into the t
step 6
insert the side pieces into the top rail and bottom
step 7
insert the stakes to the bottom of t
step 8 and very important if there is alittle wind out is to insert a screw in all 4 corners by where the claps are so that the clamps will not slide
<a href="http://s287.photobucket.com/albums/ll158/sinkgoal/?action=view&current=100_1552.jpg"
step 9 cut you some lenths of resin paper at 44" long
NOW YOU ARE READY TO PATTERN YOUR GUNS
GOOD LUCK AND GOOD HUNTING
BY THE WAY ALL MATERIALS WERE BOUGHT AT MENARDS AND THE TOTAL
WAS UNDER 17.00 DOLLARS
Thread
Thread Starter
Forum
Replies
Last Post
liquidorange
Bowhunting Gear Review
14
09-27-2007 01:51 AM