Bitzenburger jig ? straight clamp cam set-up
10-27-2009, 12:28 PM
#1
Typical Buck
Thread Starter
Join Date: Jun 2006
Posts: 882
Bitzenburger jig ? straight clamp cam set-up
I like to ask with the above jig can you set it up with a 2 degree off-set?
I don't have the instruction with the jig.
I did some 2" blazer vanes the other day and have to say what a difference in flight with broadheads when you get out to 30 yards.
I did screw up 1 shaft seem the top vane REAR was leaning to the left a little (off-center) the shaft did have a little twist to the arrow flight.
I see there is 2 marks on the jig;I would think it is set for a straight fletch (no off-set)
I think the 2" blazers are outstanding will the above jig work on blaszer vanes or would I need to purchase one that is made for blaszer vanes only.
I read a 2 degree off set is all that is needed ,I also hear some guys use a helical on blazers vanes?
any one use the above jig/ and if so what or how are the cams set-up top and bottom as far as 1/16 or 1/8" setting top and bottom
I called customer service at bitzenburger the old timer said 1/8 at the top and 1/16 at the bottom to the right (no way) the set up is wrong I thought I ask any one who uses the jig were are his cams marks top and bottom????
I don't have the instruction with the jig.
I did some 2" blazer vanes the other day and have to say what a difference in flight with broadheads when you get out to 30 yards.
I did screw up 1 shaft seem the top vane REAR was leaning to the left a little (off-center) the shaft did have a little twist to the arrow flight.
I see there is 2 marks on the jig;I would think it is set for a straight fletch (no off-set)
I think the 2" blazers are outstanding will the above jig work on blaszer vanes or would I need to purchase one that is made for blaszer vanes only.
I read a 2 degree off set is all that is needed ,I also hear some guys use a helical on blazers vanes?
any one use the above jig/ and if so what or how are the cams set-up top and bottom as far as 1/16 or 1/8" setting top and bottom
I called customer service at bitzenburger the old timer said 1/8 at the top and 1/16 at the bottom to the right (no way) the set up is wrong I thought I ask any one who uses the jig were are his cams marks top and bottom????
10-28-2009, 05:46 AM
#2
Nontypical Buck
Join Date: Nov 2008
Location: Adirondacks
Posts: 1,305
With 2" Blazers even with the helical clamp there's barely any offset let alone helical.I wouldn't worry about it just so long as the jig is properly adjusted so the fletchings base seats in full contact with the shaft.
10-28-2009, 07:41 PM
#3
Typical Buck
Thread Starter
Join Date: Jun 2006
Posts: 882
I did get it set up
I used a 1/16" on the top cam to the right
I moved the bottom cam to the left (hairline)
I think it is a good off-set how much degreess I would say more then 2 more like 3to4"
I test a few at 20 yards I will doulbe check them with broadheads at 30 yards this weekend
I used a 1/16" on the top cam to the right
I moved the bottom cam to the left (hairline)
I think it is a good off-set how much degreess I would say more then 2 more like 3to4"
I test a few at 20 yards I will doulbe check them with broadheads at 30 yards this weekend
