Go Back  HuntingNet.com Forums > Firearms Forum > Guns
 Dissing 150 Grainers?? >

Dissing 150 Grainers??

Guns Like firearms themselves, there's a wide variety of opinions on what's the best gun.

Dissing 150 Grainers??

Old 11-08-2006, 06:48 PM
  #1  
Thread Starter
 
Join Date: Nov 2006
Posts: 18
Default Dissing 150 Grainers??

I have been reading another forum.... everyone there says 150 grain bullets for a 300 magnum are no good.... what's up with that?
Joshsrugershooter is offline  
Old 11-08-2006, 06:50 PM
  #2  
Thread Starter
 
Join Date: Nov 2006
Posts: 18
Default RE: Dissing 150 Grainers??

150 gr. bullets NORMALLY require 1-12" to 1-14" rates of twist instead of a 1-10" .. WHAT THE HELL???? is that all about also
Joshsrugershooter is offline  
Old 11-08-2006, 07:01 PM
  #3  
Nontypical Buck
 
BrutalAttack's Avatar
 
Join Date: Apr 2004
Location:
Posts: 1,572
Default RE: Dissing 150 Grainers??

THere is no need to make a new thread for every sentence that pops into your head.
BrutalAttack is offline  
Old 11-08-2006, 07:13 PM
  #4  
 
Join Date: Feb 2006
Posts: 493
Default RE: Dissing 150 Grainers??

Dont believe every thing you read, non of us know it all, except for maybe Brutal Attack
fornra@yahoo.com is offline  
Old 11-08-2006, 07:44 PM
  #5  
 
Join Date: Aug 2006
Location:
Posts: 299
Default RE: Dissing 150 Grainers??

What is "dissing"? Didn't snoop dog coin that word?
ranger140892 is offline  
Old 11-08-2006, 07:52 PM
  #6  
 
Join Date: Sep 2004
Location:
Posts: 1,345
Default RE: Dissing 150 Grainers??

Umm....

1. Ask all you want, that's part of the reason this place is here...perhaps the main reason
2. Maybe they feel that using 150gr bullets is a waste of the 300magnum's potential OR maybe they feel that they don't hold up when they're pushed at 300 velocities. If that's the case go with a partitioned bullet or barnes.
3. Lighter bullets are generally shorter than there heavier partners. Shorter bullet lengths require slower twist rates to stabilize. Longer bullets require faster twist rates to stabilize. I highly doubt that .30 caliber 150gr bullets are going to have problems "flying apart" from too fast twist-rates.
Soilarch is offline  
Old 11-08-2006, 08:34 PM
  #7  
Boone & Crockett
 
James B's Avatar
 
Join Date: Feb 2003
Location: Wall SD USA & Jamestown ND
Posts: 11,474
Default RE: Dissing 150 Grainers??

150 grain bullets will work fine. HOWEVER at 300 Mag Velloocity, they can do a lot of meat damage. If you don't mind the extra damage, go ahead and use them. The 180 grain is just a better choice for the 300 Win Mag. I know because I have tried both. If I were to use 150 grain bullets, I would load them down to about 2800 fps. JMO.
James B is offline  
Old 11-08-2006, 08:41 PM
  #8  
Nontypical Buck
 
Join Date: Aug 2004
Location:
Posts: 1,290
Default RE: Dissing 150 Grainers??

Heh, heh, James, did they pass-through at all? My coworker was talking about the last deer he got with an '06. Great mushroom, turned the lungs to goo, the deer dropped straight down and did not move a step!
biscuit jake is offline  
Old 11-08-2006, 10:38 PM
  #9  
Nontypical Buck
 
Join Date: Jan 2004
Location: Baileysville, WV
Posts: 2,925
Default RE: Dissing 150 Grainers??

heeeeeeeeess baaaaaaaacckkkk
Doe Dumper is offline  
Old 11-09-2006, 07:54 AM
  #10  
 
Join Date: Sep 2006
Location:
Posts: 4,553
Default RE: Dissing 150 Grainers??

I took a doe with my .300 win mag using 165 grn Fail safes this past Saturday and it did some good damage to the shoulder. Actually pretty much wrecked the shoulder. I used the 165 grn, as I was getting 1" groups at 100 yards and 2-3" groups at 200 yards.
Red Lion is offline  

Quick Reply: Dissing 150 Grainers??


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.