Mountaineer Came Monday
#22
Nontypical Buck
Joined: Dec 2009
Posts: 2,496
Likes: 0
From: Yucca Valley,Ca
We also have steep rough country to hunt where I live, deep ravines ect. Like I mentioned above somewhere I prefer a heavier rifle as Im Big and Tall, it just fits me better. I just turned 50 this past Dec 31st but during the last day of our hunting season this year I still managed to drag a buck back to my truck with my accura 1 1/2 miles, it felt good. I realize ssome hunt bigger animals than whitetails, if I had Elk to hunt then I bet ya I'd go for a lighter Mler.
Im just picking everyone's bones on this one, I have the urge to get a new mler but I dont know what it will be as of yet. I have'nt seen the new CVA mountain rifle yet but being a CVA shooter I'll check it out.
I'll follow the post on the knight mountaineer and see what everyone has to say, and your right if I like what Im now using than why change....but you all know the urge to buy something new....still way undecided.
(BP)
Im just picking everyone's bones on this one, I have the urge to get a new mler but I dont know what it will be as of yet. I have'nt seen the new CVA mountain rifle yet but being a CVA shooter I'll check it out.
I'll follow the post on the knight mountaineer and see what everyone has to say, and your right if I like what Im now using than why change....but you all know the urge to buy something new....still way undecided.
(BP)
#24
Thread Starter
Nontypical Buck
Joined: Aug 2008
Posts: 3,732
Likes: 0
From: Rapid City, South Dakota
This morning i removed the scope from the Extreme (Chet' rifle), and installed it on the Mountaineer. For the first time in my life, the scope ended up too low. Took it shooting any way. Struggled with the sight picture. After getting the shots to hit paper, and kinda getting a 100 yard zero, i moved out to 200 yard. Photo show 4 shot. Green marks the last shot, which cut the bottom support of the target frame, and ended the shooting. I believe them 4 shot were the tenth, eleventh, twelfth, and thirteenth from this rifle.

The load used doesn't seem all that good. 270g Deep Curl, 110g BH, crush rib sabot, W209 primer. There were no issues during the shoot, except for i couldn't see the whole view through the scope. Primer were easy to install, and they fell right out after firing. It was cold when we started, and colder when we finished. It was 9 degree when we headed home.
After cleaning the rifle, i removed, and replaced the scope so now it is a near perfect height, at least for my face.

Blow by was zero. Breeze was on again off again.

The load used doesn't seem all that good. 270g Deep Curl, 110g BH, crush rib sabot, W209 primer. There were no issues during the shoot, except for i couldn't see the whole view through the scope. Primer were easy to install, and they fell right out after firing. It was cold when we started, and colder when we finished. It was 9 degree when we headed home.
After cleaning the rifle, i removed, and replaced the scope so now it is a near perfect height, at least for my face.
Blow by was zero. Breeze was on again off again.
#25
Im sure it'll all come togeather.
Now I know evey one has there own way of sighting in, but give this a try I learned it from sighting in a Bow.
Draw a Horizional Line about a 1/2" thick accross a sheet of paper around a foot long. Dont worry about left or right, just get the shots so there hitting the line or dang close to it. Then get a new piece of paper and draw a line up and down (perpindicular) again about a foot long and a 1/2" wide and sight in for left and right, and again try and get em right on the line. After you have distance and right and left on then get your normal target and go for it.
The (line) method makes you focus only on one thing, either up and down or right and left, not both at the same time. You'll be surprised at how much tighter your groups will get with this method. And yes I know this is a new MLer and you had to adjust your scope for proper fit, I was just giving you and others a different way to sight in, hope you like it and give it a try.
(BP)
Now I know evey one has there own way of sighting in, but give this a try I learned it from sighting in a Bow.
Draw a Horizional Line about a 1/2" thick accross a sheet of paper around a foot long. Dont worry about left or right, just get the shots so there hitting the line or dang close to it. Then get a new piece of paper and draw a line up and down (perpindicular) again about a foot long and a 1/2" wide and sight in for left and right, and again try and get em right on the line. After you have distance and right and left on then get your normal target and go for it.
The (line) method makes you focus only on one thing, either up and down or right and left, not both at the same time. You'll be surprised at how much tighter your groups will get with this method. And yes I know this is a new MLer and you had to adjust your scope for proper fit, I was just giving you and others a different way to sight in, hope you like it and give it a try.
(BP)
#28
Thread Starter
Nontypical Buck
Joined: Aug 2008
Posts: 3,732
Likes: 0
From: Rapid City, South Dakota
It was 3 degree when i left town. It was 7 degree when the shooting started. It was 23 degree when the powder was gone. Upon returning home the temperature was 9. This was one of them day when it was colder in town than up in the hills.
The rifle had to be sighted in all over again, because the scope was removed, and replaced. Again there was zero blow by. Again the primers fell right out. When the shooting ended, there had been a total of 33 shots through the rifle, after 2 shooting trips. The installation of the primer is becoming more and more routine. Using the pointer finger to push the primer against the bolt face has become second nature. Installing the primer is easy, even with the scope in place. The bolt does not reveal it has seen 33 shot; it is so clean.

The target was at 200 yard. The 3 shot in the red were made first. Then the other two followed. The load was 300g Deep Curl, 110g BH, crush rib sabot, W209 primer.
The cross hair wasn't proper, so i reinstalled the scope again. This was done this afternoon, after cleaning the rifle. Once again, the next time shooting, will involve re-zero the scope. Hopefully this time the initial sight in will be completed the third try.
The rifle had to be sighted in all over again, because the scope was removed, and replaced. Again there was zero blow by. Again the primers fell right out. When the shooting ended, there had been a total of 33 shots through the rifle, after 2 shooting trips. The installation of the primer is becoming more and more routine. Using the pointer finger to push the primer against the bolt face has become second nature. Installing the primer is easy, even with the scope in place. The bolt does not reveal it has seen 33 shot; it is so clean.
The target was at 200 yard. The 3 shot in the red were made first. Then the other two followed. The load was 300g Deep Curl, 110g BH, crush rib sabot, W209 primer.
The cross hair wasn't proper, so i reinstalled the scope again. This was done this afternoon, after cleaning the rifle. Once again, the next time shooting, will involve re-zero the scope. Hopefully this time the initial sight in will be completed the third try.
#30
Thread Starter
Nontypical Buck
Joined: Aug 2008
Posts: 3,732
Likes: 0
From: Rapid City, South Dakota


