Sharpening Carbon steel
#1
Nontypical Buck
Thread Starter
Join Date: Feb 2003
Location:
Posts: 2,994
Sharpening Carbon steel
I'm trying to sharpen my Wensel Woodsmans (brand new) using varying grit diamond stones (180, 260, 360, 600, 1200) then finishing them off on 2000 grit automotive sandpaper.
They seem to be sharp, easily grab my fingernail and snap a stretched rubber band with minimal pressure applied. Can't get them to shave, but I think that's cause I'm using the wrong technique.
When I've done this with stainless, the edges were polished and shiny, mirror like. The carbon steel doesn't have this appearance. Is that a factor of the material or do I not have them as sharp as they could be?
They seem to be sharp, easily grab my fingernail and snap a stretched rubber band with minimal pressure applied. Can't get them to shave, but I think that's cause I'm using the wrong technique.
When I've done this with stainless, the edges were polished and shiny, mirror like. The carbon steel doesn't have this appearance. Is that a factor of the material or do I not have them as sharp as they could be?
#2
Giant Nontypical
Join Date: Feb 2003
Posts: 9,175
RE: Sharpening Carbon steel
I think it's a function of the edge angle you're forced into with a 3-blade head. It's just too steep to really put a hair popping razor edge on them. I've never used Snuffers because I can't get that really scary edge I get with my 2-blade heads.
I've recently gone to Magnus' website and checked out their sharpening instructions for Snuffers. They say touse only a 10" medium mill bastard file, form a burred edge and leave the burr alone. I've always tried to remove the burr and put that razor edge on 'em, and was never satisifed with the results. Obviously, that's where I went wrong.[&:]
Since the Woodsman is basically a stretched out version of the Snuffer, I'd say the same sharpening method should work for them too. Maybe I'll get a chance to try out that sort of edge on a few Snuffers before the woods get too much older.
I've recently gone to Magnus' website and checked out their sharpening instructions for Snuffers. They say touse only a 10" medium mill bastard file, form a burred edge and leave the burr alone. I've always tried to remove the burr and put that razor edge on 'em, and was never satisifed with the results. Obviously, that's where I went wrong.[&:]
Since the Woodsman is basically a stretched out version of the Snuffer, I'd say the same sharpening method should work for them too. Maybe I'll get a chance to try out that sort of edge on a few Snuffers before the woods get too much older.
#3
Nontypical Buck
Thread Starter
Join Date: Feb 2003
Location:
Posts: 2,994
RE: Sharpening Carbon steel
Did they get shiny?
I'm gonna have to get my hands on a file. Lots of guys at tradgang swear by a file, some follow with a bit on a fine diamond stone then leather, and say they shave hair.
What's the difference between a bastard mill file and a single cut? Which is preferred for sharpening 3 bladers, if it matters?
I'm gonna have to get my hands on a file. Lots of guys at tradgang swear by a file, some follow with a bit on a fine diamond stone then leather, and say they shave hair.
What's the difference between a bastard mill file and a single cut? Which is preferred for sharpening 3 bladers, if it matters?
#4
Giant Nontypical
Join Date: Feb 2003
Posts: 9,175
RE: Sharpening Carbon steel
A bastard file is a single cut, but it's a finer cut than a plain single.Kinda like the difference between coarse sandpaper and fine. Size also makes a difference. A big file is coarser than a small one. So, when theyrecommend a 10" file, then they must have found out that particular size and cut works best for the edge they recommend. Nicholson makes a good file and I've seen 'em even at wally world.
#5
Nontypical Buck
Join Date: Feb 2003
Location: west central wi USA
Posts: 2,242
RE: Sharpening Carbon steel
I sharpened a buddy's Woodsmans for him. I started with a regular carborundum stone, went to a hard Arkansas stone, finally, a piece of ground glass, and stropped it on a piece of cardboard. They would shave when I finished. I think your abrasives might be a little coarse.
Thread
Thread Starter
Forum
Replies
Last Post
buckeye
Archery Gear
0
03-08-2006 06:17 PM