HuntingNet.com Forums - Search Results
HuntingNet.com Forums

Go Back  HuntingNet.com Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Search: Posts Made By: Roger Barker
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Forum: Crossbows
09-01-2007, 05:41 AM
Replies: 9
Views: 1,943
Posted By Roger Barker

RE: Crossbow bolts

jedge1979,

I'm new to crossbows, but I'll post my impression to perhaps stimulate some opinions based on more experience. It seems the power of crossbows result in a lot of bent aluminum bolts....
Forum: Crossbows
08-31-2007, 07:54 PM
Replies: 4
Views: 3,128
Posted By Roger Barker

RE: Arrow Retention Spring on Horton Summit Lifts Bolt?

Guys,

I talked to Horton today. They suggested the problem was caused by pushing the bolt too hard into the string when loading. I verified this as the cause. Push the bolt into the string and...
Forum: Crossbows
08-27-2007, 07:25 PM
Replies: 4
Views: 3,128
Posted By Roger Barker

Arrow Retention Spring on Horton Summit Lifts Bolt?

Horizontal Limb Guys,

The arrow retention spring on my new Horton Summit applies enough pressure on the bolt to lift it slightly in the track. I'd say the bolt is up maybe 1/32" at the front end...
Forum: Crossbows
08-27-2007, 07:10 PM
Replies: 11
Views: 1,118
Posted By Roger Barker

RE: Point of Inpact Shifts Right Off-hand?

Thanks for all the ideas, guys. This weekend I'll do some more shooting to see if I can confirm any of these possible causes. I'll let you know what I find out.

Thanks again,

Roger
Forum: Crossbows
08-27-2007, 04:42 PM
Replies: 6
Views: 7,188
Posted By Roger Barker

RE: Horton Summit Trigger Assembly & Dial-A-Range Removal?

Thanks for the input, guys. Awshucks, please post a link to the AT xzbow forum. I'd like to check it out.

Thanks,

Roger
Forum: Crossbows
08-26-2007, 07:57 PM
Replies: 6
Views: 7,188
Posted By Roger Barker

RE: Horton Summit Trigger Assembly & Dial-A-Range Removal?

awshucks,

Thanks. I saw the thread here. I will probably lock the dial-a-range. I have noticed it moving when I cock the Summit. I would still like to know the procedure for removing the...
Forum: Crossbows
08-26-2007, 07:15 PM
Replies: 11
Views: 1,118
Posted By Roger Barker

RE: Point of Inpact Shifts Right Off-hand?

awshucks,

Thanks. I am using a rope cocker.

Roger
Forum: Crossbows
08-26-2007, 07:13 PM
Replies: 11
Views: 1,118
Posted By Roger Barker

RE: Point of Inpact Shifts Right Off-hand?

GrumpyTom & Pydpiper,

Thanks for the input. I'm pretty sure I'm holding the limbs level. I have been making a conscious effort to do so. This shooting has been at 20 yards in my basement. I also...
Forum: Crossbows
08-26-2007, 12:14 PM
Replies: 11
Views: 1,118
Posted By Roger Barker

Point of Inpact Shifts Right Off-hand?

All,

I'm new to crossbows. I sighted in kneeling and supporting my right elbow on a table. The sight picture was very steady. Shooting off-hand, the bolts impact right. Is this a common...
Forum: Crossbows
08-26-2007, 12:06 PM
Replies: 6
Views: 7,188
Posted By Roger Barker

Horton Summit Trigger Assembly & Dial-A-Range Removal?

All,

Can someone provide me with instructions for removal of the dial-a-range and trigger assembly from the Summit 150 stock? I want to remove itto clean and lub.

Thanks,

Roger Barker
Forum: Archery Gear
02-12-2005, 07:49 AM
Replies: 1
Views: 728
Posted By Roger Barker

WTB PSE Monarch

Archers,

I'm looking to buy a PSE Monarch with the shoot thru riser. I believe they were last made in 2002. Let me know what you have and what you're looking to get for it.

Thanks,

...
Forum: Technical
12-31-2004, 10:09 AM
Replies: 4
Views: 3,467
Posted By Roger Barker

RE: Devastator Crossbow Disassemble Trigger?

DoninVa,

Thanks for the tip. Please post a link for the cross gun forum if you have one. I'm thinking some of the guys on this forum will have some crossbow knowledge.

Roger
Forum: Technical
12-31-2004, 07:12 AM
Replies: 4
Views: 3,467
Posted By Roger Barker

Devastator Crossbow Disassemble Trigger?

Fellow Archers,

I have Bear-Jennings devastator crossbow and want to disassemble, clean and dry lub the trigger mechanism. (I have worked on my own compound bows, releases, and firearms for...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.