Lee hand priming tool does not like 300 WSM
07-10-2004 | 09:43 AM
#1
Thread Starter
Typical Buck
Joined: Apr 2004
Posts: 982
Likes: 0
From: Central Michigan
Lee hand priming tool does not like 300 WSM
My dad has a Lee hand priming tool and it worked just fine until I got a 300 WSM. The 300 WSM has the same diameter rim as a 7mm Remington Mag but is fatter past were the belt is on the 7mm mag. It is too FAT for the Lee hand priming tool. I have to use the primer on my RCBS press I dont like as well. Does the RCBS hand priming toll work with the short mags?
07-10-2004 | 11:01 PM
#7
Joined: Aug 2003
Posts: 77
Likes: 0
From: Denver, CO
RE: Lee hand priming tool does not like 300 WSM
I believe I heard once that Lee would fix that if you sent the unit to them. If not, it's easy to correct with a rat tail file or similar tool to increase the clearance. Good luck.
07-11-2004 | 06:11 AM
#8
Typical Buck
Joined: Feb 2003
Posts: 964
Likes: 0
From: Hickory NC USA
RE: Lee hand priming tool does not like 300 WSM
Have a lee hand primer using #5 shell holder it does fine with 7 mm and wsm,(300 0r 270 wsm )Maybe they fixed it before I got mine though.It is the one that holds the primers in a round disc.Have an older model that you load one at a time but cannot find a mag shell holder for it ,I like it better than the new one.
07-11-2004 | 06:20 PM
#9
Giant Nontypical
Joined: Feb 2003
Posts: 6,471
Likes: 0
From:
RE: Lee hand priming tool does not like 300 WSM
The RCBS shell plate #43 is for the five station and Ammomaster and the Pro2000
07-16-2004 | 01:08 PM
#10
Joined: May 2004
Posts: 10
Likes: 0
From:
RE: Lee hand priming tool does not like 300 WSM
Huh? - I'm a little confused here or at least I'm having trouble tellng the apples from the oranges.
My Lee hand tool takes Lee shell holders designed soley for it. These holders have no mounting stem - they are essential the top half of the equivalent shell holder for a press. My RCBS handtool takes any standard shell holder designed for single stage presses. I've never tried installing an RCBS shell holder in the Lee tool.
Also Lee and RCBS and most other mfg's use different numbering systems so that to use you need to match the case your using to a list provided by that mfg. For instance it's not likely that a LEE #3 is the same as an RCBS #3.
One thing that RCBS does is keep the shell holder number uniform across their product line. So that is the case takes a #3 shellholder in the press then the correct shellholder for the RCBS trimmer will also be #3 even though it's an entirely different part - I'm assuming this is tru also of their shell plates for their progressive equipment.
My Lee hand tool takes Lee shell holders designed soley for it. These holders have no mounting stem - they are essential the top half of the equivalent shell holder for a press. My RCBS handtool takes any standard shell holder designed for single stage presses. I've never tried installing an RCBS shell holder in the Lee tool.
Also Lee and RCBS and most other mfg's use different numbering systems so that to use you need to match the case your using to a list provided by that mfg. For instance it's not likely that a LEE #3 is the same as an RCBS #3.
One thing that RCBS does is keep the shell holder number uniform across their product line. So that is the case takes a #3 shellholder in the press then the correct shellholder for the RCBS trimmer will also be #3 even though it's an entirely different part - I'm assuming this is tru also of their shell plates for their progressive equipment.
Thread
Thread Starter
Forum
Replies
Last Post
Dubbya
Automotive
0
01-14-2009 08:17 AM
