RE: 12GA From Hell
 

Some 8GA FH testing- using IMR 4759, 770 gr slug,
top load of 140 gr, got 2500 fps......
Over 10,000 ft lbs..Cases extract easy.
The plastic in 8ga case is twice as thick as
in 12ga cases. Tried 4227 and case is too large
diameter for dependable ignition.So it's
old dependable 4759..Ed

[/align]

RE: 12GA From Hell
 

Here is picture of Enfield 8GA FH. You can see plastic case
in the port. Box of cases behind, 770 gr and 1050 gr
slugs in front with the 8ga wadcups I use.
Left two slugs are 1050 gr made from 3 oz kiln slugs.
I rounded nose and put in hollow base. Also the
cards and fiber wads used. Slugs are hollowbase, as
it is smooth bore barrel. Ed

RE: 12GA From Hell
 

In picture of the 8ga bolt action you can see the
ring I put on front of bolt to support large diameter
8ga casehead. It is suported against thrust by the
front lugs, and total bolt thrust is supported by rear
lugs and have taken the heavy loads ok.. Ed

RE: 12GA From Hell
 

Here is picture on left of the 12ga hollowpoint slug
with plastic tip. Makes it streamlined, good for 300yds.
And still will expand good thin skinned game-deer.
I put tip in with glue gun in few seconds, and
shaped a point on it with trim knife. Ed

RE: 12GA From Hell
 

I also have two other cartridges with my name
on them that I am promoting. They are my 700HE
and my 585BHE. They both belted straight cases.
Montana Rifle company is coming out with their
big PH action and some guys will be doing my
cases in them.
Info on the 585BHE. It will work in
any gun that handles 505 Gibbs like Enfield, CZ,
Ruger,etc.Mine is in Enfield.Here is picture of
of one next to Trex. And mine holds 15gr more
powder than that Trex case. 585BHE will do 750
grain from 1800 to 2800 fps in my Enfield.
Anyone interested setting up a gun, contact me
I will furnish reamer and 15 free cases. Cases are
headstamped. When done return reamer to me, for
the next guy. I will keep them sharpened. After a
few guys have guns we all will get together with
others wanting some and get a run of brass made.
These cases are all drawn high pressure brass.
I'd like guys to ask for reamer when gun is going
to be ready to chamber, that way reamers get the
most guns done in shortest time.Ed

RE: 12GA From Hell
 

On Fri May 2 8pm on the Science Channel ,they will have
an article about the heavy barrel cannons that shoot
the brass cases for bomb disposal.They are the same as
our 12GA FH case,when resized in my dies and are shown
in this thread a couple months back in picture.
It will show them using them for bomb disposal. Ed[/align]

RE: 12GA From Hell
 

Testing 8GA FH in Enfield, 1050 gr slug in wad cup, 120 gr
of 4759, over 2000 fps. Cases extract easy. Hardly any
base cup expansion...Ed

RE: 12GA From Hell
 

Here is picture of a sectioned 8ga plastic case
showing how heavy and strong it is built. The
plastic is one piece compressioned formed and
the sides of the cases are twice as thick as
12ga cases.You can see the double thickness
of the base cup. Ed

RE: 12GA From Hell
 

Here is picture of the bolt setup for the 8ga
Enfield we did.Also comparison to a Mauser
12ga shotgun bolt conversion, from which
I got the concept. Ed

RE: 12GA From Hell
 

Ed,

I look into your post every once in a while and my immediate thought everytime is how the heck do you finance all this research. So how do you?

Are you ultimately after some kind of profit motive? Or is this truly just fun times?

I will admit it is interesting reading up on your pursuits.

Tom