|
RE: Impressed w/ 2008 General!
I was about to ask if you've tightened the mods, but guess that answered my question. You may also check the string suppressor pocket or whatever you call it. It has some allen screws, but I doubt it would cause as much vibration as you have described. Best of luck, don't write the bow off, it's a great hunting bow.
|
RE: Impressed w/ 2008 General!
Its not the mods and you're exaggerating that you can feelanything after the shot.;)
It's your cam/axel spacers. Somebody in the build room left out a cam spacer and the 2 little ones are buzzing against each other on the shelf side of the cam. You can probably drop a finger in there and spin them by hand. Look closely at the gap between the limb cap and the cam surface, if you can see axel or move the spacer/s by handthen the spacer is wrong. Throw it in a press,bring the axel out 1/3 of the way to drop the spacers on that side and swap out with a .112" solid single spacer. Thats what I did for mine because when I would flick the cam with my finger to check the mod screws I was getting a buzz on mine. If you don't have on hand have the shop guy call Bowtech for spacers. Trust me someone at Bowtech got a punch in the temple for that one but I think a couple got out the door like that. :eek:Its a $.05 / 5 minute fix but annoying nontheless. I can almost guarantee you that's the problem and it's aquickie fix. |
RE: Impressed w/ 2008 General!
As standard procedure I always , BEFORE I shoot any bow, check all the mod screws ( i even use blue loctite on them) check e-clips, suppressors, you name it. The bow pretty much gets the once over. I usually have success with it after that. Archery is a sport of detail. BYthe way I am getting 278ft per sec with a 350gr arrow @ 26" not too bad.
|
RE: Impressed w/ 2008 General!
ORIGINAL: Matt / PA Its not the mods and you're exaggerating that you can feelanything after the shot.;) It's your cam/axel spacers. Somebody in the build room left out a cam spacer and the 2 little ones are buzzing against each other on the shelf side of the cam. You can probably drop a finger in there and spin them by hand. Look closely at the gap between the limb cap and the cam surface, if you can see axel or move the spacer/s by handthen the spacer is wrong. Throw it in a press,bring the axel out 1/3 of the way to drop the spacers on that side and swap out with a .112" solid single spacer. Thats what I did for mine because when I would flick the cam with my finger to check the mod screws I was getting a buzz on mine. If you don't have on hand have the shop guy call Bowtech for spacers. Trust me someone at Bowtech got a punch in the temple for that one but I think a couple got out the door like that. :eek:Its a $.05 / 5 minute fix but annoying nontheless. I can almost guarantee you that's the problem and it's aquickie fix. The other problem I had on mine was a twisted limb, but thats another story. |
RE: Impressed w/ 2008 General!
ORIGINAL: Alex Nenadic ORIGINAL: Matt / PA Its not the mods and you're exaggerating that you can feelanything after the shot.;) It's your cam/axel spacers. Somebody in the build room left out a cam spacer and the 2 little ones are buzzing against each other on the shelf side of the cam. You can probably drop a finger in there and spin them by hand. Look closely at the gap between the limb cap and the cam surface, if you can see axel or move the spacer/s by handthen the spacer is wrong. Throw it in a press,bring the axel out 1/3 of the way to drop the spacers on that side and swap out with a .112" solid single spacer. Thats what I did for mine because when I would flick the cam with my finger to check the mod screws I was getting a buzz on mine. If you don't have on hand have the shop guy call Bowtech for spacers. Trust me someone at Bowtech got a punch in the temple for that one but I think a couple got out the door like that. :eek:Its a $.05 / 5 minute fix but annoying nontheless. I can almost guarantee you that's the problem and it's aquickie fix. The other problem I had on mine was a twisted limb, but thats another story. |
RE: Impressed w/ 2008 General!
I really want to try a Bowtech as I have been a Mathews man forever; but stories like this make me wonder. The build team is aware of these end caps and it's only supposed to be a batch of them that went out this way and their is a QC person checking each one to make sure the fit is correct. Bowtech will supply any dealer with the replacement parts to take away any buzz that the gap might cause. They won't all be like that obviously but if you're one of the lucky early ones that were in that batch (like myself) it's seriously a 5 minute no hassle fix. (if that) |
RE: Impressed w/ 2008 General!
I really want to try a Bowtech as I have been a Mathews man forever; but stories like this make me wonder. |
| All times are GMT -8. The time now is 01:55 PM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.