Slick Trick blades fit loose?
10-19-2006 | 09:18 PM
#1
Thread Starter
Nontypical Buck
Joined: Oct 2005
Posts: 2,355
Likes: 0
From: Flushing Michigan
Slick Trick blades fit loose?
Has anybody noticed the 2006 blades don't seem to fit tight together? Even when I use a broadhead wrench the blades seem to move around a little. When i tap my quiver full of slick tricks there is a vibration caused by the fact that they locktight together.
They still shoot great but I wish they locked down tight. Or am I doing something wrong?
They still shoot great but I wish they locked down tight. Or am I doing something wrong?
10-20-2006 | 06:54 AM
#2
Joined: Mar 2004
Posts: 158
Likes: 0
From:
RE: Slick Trick blades fit loose?
I don't have the '06 version, but I have packs for the past 3 years. All fit tight, but you do have to use the small washer that comes with them. I initially thought I could get away without it and just have them fit up flush to the broadhead adapter ring (I shoot Axis 340 arrows), but they were slightly loose on that. Once the washer was used everything was tight. When getting the broadhead to spin true, I found that the small washer can help get them aligned by loosening the head, spinning the washer a fraction of a turn, then tightening back down.
10-20-2006 | 08:38 AM
#3
Nontypical Buck
Joined: Feb 2003
Posts: 2,599
Likes: 0
From: Crosby TX USA
RE: Slick Trick blades fit loose?
I recently swapped out all of my blades with the new German blades and found that they all were tight with no slop- I use the washers.
While swapping them out I noticed some of my old ones had a rounded rear edge that sits inside the furrel and most were squared off. I bet the rounded ones were the loose ones.
The new German blades have a larger ground edgeand are super scary sharp. I compared several to the old blades and each one was slightly larger from outside edge to outside edge. Maybe a couple of 32" wider overall.
I did use the old washers on some arrows to make thebladesline up the way I like ( 2verticle, 2 horizontal) the newer washers are a tad taller than the old.
While swapping them out I noticed some of my old ones had a rounded rear edge that sits inside the furrel and most were squared off. I bet the rounded ones were the loose ones.
The new German blades have a larger ground edgeand are super scary sharp. I compared several to the old blades and each one was slightly larger from outside edge to outside edge. Maybe a couple of 32" wider overall.
I did use the old washers on some arrows to make thebladesline up the way I like ( 2verticle, 2 horizontal) the newer washers are a tad taller than the old.
10-20-2006 | 08:43 AM
#4
Nontypical Buck
Joined: Feb 2003
Posts: 3,318
Likes: 0
From: Norman OK USA
RE: Slick Trick blades fit loose?
At one point I had one that didn't seem like it fit tight, and then I realized that I failed to put the washer on that particular arrow. I have 13 slick tricks and they all fit tight as of last night.
10-20-2006 | 09:11 AM
#5
Nontypical Buck
Joined: Aug 2005
Posts: 3,180
Likes: 0
From: Cenral Illinois
RE: Slick Trick blades fit loose?
My old ones fit together real good and so do the new ones. They are a little hard to put together without getting cut though! Use caution with the new blades, they are REALLY SHARP!
10-20-2006 | 12:56 PM
#8
Nontypical Buck
Joined: Feb 2003
Posts: 1,983
Likes: 0
From: Sturgis, SD
RE: Slick Trick blades fit loose?
I have the 06 125gr magnum heads and all of mine fit tight. I'm using the enclosed washers as well. Scary sharp is an understatement. They stay sharp as well, like nothing I have ever seen.
