Cooking a Barrel
#1
Cooking a Barrel
Last week after getting home from my second shoot with the re-claimed Knight Super DISC I decided to strip clean the barrel to get all the oils and residues out as I wanted to treat it with Dyna-Tek Bore Coat. I purchased this Super DISC knowing that the barrel was probably pitted, but believing it could be saved. I had already ran a JB bore treatment on the bore and installed a new crown. The shooting I did with the rifle earlier in the week convinced me this rifle was going to work well. The bullet I want to use in this rifle is a 40 x 230 grain Lehigh brass bullet. Because of its weight it is very long and requires a fast twist bore to stabilize the bullet.
This is the bullet I am talking about.
It doesn't look abnormally long here in the picture shown above, but when you insert it in a sabot it becomes very noticeable.
The Super DISC with its 1/20 twist rate is an excellent rifle to shoot this bullet.
Because everything was working out so well as I have stated above I decided I really wanted to treat the bore with Dyna-Tek. I actually even read the directions that came with the product.
After applying the Ceramic fluid in the bore the last part of the instructions was allow the bore to dry and then shoot approximately 6 shots through the bore to apply heat and pressure to the bore. Todays shoot was to get this task done.
I normally do not shoot BH but in reality this would be an excellent powder for this application... it burns hotter and longer than T7 - so it should really accomplish the task. I pre-measure out 120 grains of BH and dropped it into powder tubes. I loaded 10 tubes, thinking a couple of extra couldn't hurt. Equipped with this I really felt I could 'cook' the barrel with shot after shot with no or very little cooling time between shots.
I walked 6 birds out to 100 yards walked back loaded and began shooting. The first 6 shots went just as planned - 6 shattered birds. This set of pictures kind of shows the results of the shooting.
I still had 4 shots left and began searching the ground in the snow looking for additional targets. I found chunk of stubble sticking out of the snow at about 107 yards according to the range finder. Two of my remaining shots were shot at this target of opportunity with excellent results...
Then I looked for a more distant target - found a chunk of stubble way up the draw. Tried to range it from the bench but could not get the finder to get a reading over the snow - I moved the finder horizontally to a bare spot of earth and it returned a reading of 230 yards.
Loaded the rifle and sat down at the bench. The scope I am using is a rifle scope with a 600 yard ballistic reticule. There is a picture of the reticule in the next composite. I used the second mil-dot under the cross hair and held the dot right on the target. First shot was just right and under the target. Loaded up the final shot - used the same hold but moved the dot the left edge of the piece stubble, touched the shot off. It definitely came left and it was identical it printed right next to the first shot.
I walked out to get pictures and also to shoot a range back to the truck... It turns out I was about 5" low slightly right with the first shot and almost direct on with the second shot. Shot the range back to the truck (the small black dot in the picture) from the target - 240 yards. Over that open field the range really seems much farther but without trees or any thing to get a apparent size and distance of any thing.
Gotta go clean now...
This is the bullet I am talking about.
It doesn't look abnormally long here in the picture shown above, but when you insert it in a sabot it becomes very noticeable.
The Super DISC with its 1/20 twist rate is an excellent rifle to shoot this bullet.
Because everything was working out so well as I have stated above I decided I really wanted to treat the bore with Dyna-Tek. I actually even read the directions that came with the product.
After applying the Ceramic fluid in the bore the last part of the instructions was allow the bore to dry and then shoot approximately 6 shots through the bore to apply heat and pressure to the bore. Todays shoot was to get this task done.
I normally do not shoot BH but in reality this would be an excellent powder for this application... it burns hotter and longer than T7 - so it should really accomplish the task. I pre-measure out 120 grains of BH and dropped it into powder tubes. I loaded 10 tubes, thinking a couple of extra couldn't hurt. Equipped with this I really felt I could 'cook' the barrel with shot after shot with no or very little cooling time between shots.
I walked 6 birds out to 100 yards walked back loaded and began shooting. The first 6 shots went just as planned - 6 shattered birds. This set of pictures kind of shows the results of the shooting.
I still had 4 shots left and began searching the ground in the snow looking for additional targets. I found chunk of stubble sticking out of the snow at about 107 yards according to the range finder. Two of my remaining shots were shot at this target of opportunity with excellent results...
Then I looked for a more distant target - found a chunk of stubble way up the draw. Tried to range it from the bench but could not get the finder to get a reading over the snow - I moved the finder horizontally to a bare spot of earth and it returned a reading of 230 yards.
Loaded the rifle and sat down at the bench. The scope I am using is a rifle scope with a 600 yard ballistic reticule. There is a picture of the reticule in the next composite. I used the second mil-dot under the cross hair and held the dot right on the target. First shot was just right and under the target. Loaded up the final shot - used the same hold but moved the dot the left edge of the piece stubble, touched the shot off. It definitely came left and it was identical it printed right next to the first shot.
I walked out to get pictures and also to shoot a range back to the truck... It turns out I was about 5" low slightly right with the first shot and almost direct on with the second shot. Shot the range back to the truck (the small black dot in the picture) from the target - 240 yards. Over that open field the range really seems much farther but without trees or any thing to get a apparent size and distance of any thing.
Gotta go clean now...
#4
Dave a I use a Point Blank Range system to sight my rifle in. The first step is to shoot the load and projectile through a chronograph and that velocity. From I run the load on a ballistic calculator.
In my case I use a 6" PBR for a ML - knowing then that through the ranges my bullet will never be higher or lower than 3" through the given range.
So the ballistic sheet on the 40x230 would look like this
Showing you:
@ 25 yds the bullet is 0.47"
@ 50 yds up 1.91"
@ 75 yds up 2.176
@ 100 up 2.97"
Also the sheet shows that you can shoot this bullet from 0 to 204 yards and be within the 3" range. Also showing that @ 166 yrds. the bullet should be right at zero...
Al of this is just math so you really have to actually shoot the ranges and see where the bullet impacts. I found out the other day it was very close.
I will tell you after shooting today, especially the 240 yard shots - I did move the windage 2 clicks left and the elevation up 2 clicks.
I based these move on the shooting today. At 100 I was holding the xhair slightly under the bird and still hitting down in the bird. then at 240 I was and have been right on the last two tests.
I really should use a real target but it is so much more fun to shoot some thing that breaks.
The biggest reason I use the Ceramic compound is to seal the pits that are in the bore - plus it really does cut down on residue in the bore and hence it is easier to clean...
Sealing the bore really is my largest reason...
#6
Sabot Isn't this the same rifle you shot on your last post and was hitting a tad to the right then? If so, maybe you should give the scope a click or two to the left.
As for the dyna tek - what is the purpose of using it? Is it to fill in any minor bore deficiencies or to aid in reducing fouling or increase accuracy or all of the above?
As for the dyna tek - what is the purpose of using it? Is it to fill in any minor bore deficiencies or to aid in reducing fouling or increase accuracy or all of the above?
#7
Sabot Isn't this the same rifle you shot on your last post and was hitting a tad to the right then? If so, maybe you should give the scope a click or two to the left.
As for the dyna tek - what is the purpose of using it? Is it to fill in any minor bore deficiencies or to aid in reducing fouling or increase accuracy or all of the above?
As for the dyna tek - what is the purpose of using it? Is it to fill in any minor bore deficiencies or to aid in reducing fouling or increase accuracy or all of the above?
Correct again - all the above. The driving reason for me was to fill the pits with the ceramics - and to smooth the whole bore out. It does make it easier to clean!
#9
Sure it would work in side hammers also...
The big thing is to get every bit of oil and fouling out of the bore you can... I even go back to the boiling water rinse to insure I have the oils out of the metal pores of the bore.
#10
Sabot, the absolute best thing I have found to assure absolutely NO oils are left is Brake Cleaner. Just make sure you don't get any on ANYTHING other than the steel. That stuff will really do a number on plastics and wood. Pretty darn cheap and much easier than most other degreasers and boiling methods. You can grab a can at pretty much any auto supply. It's what the stuff is designed for. Taking the oil off disc rotors before installation. Leaving the oil on will crystallize your pads.