HuntingNet.com Forums

HuntingNet.com Forums (https://www.huntingnet.com/forum/)
-   Technical (https://www.huntingnet.com/forum/technical-20/)
-   -   cutting carbon arrows (https://www.huntingnet.com/forum/technical/348665-cutting-carbon-arrows.html)

Hooter56 08-24-2011 10:42 AM

cutting carbon arrows
 
What is the best method for cutting my carbon arrows to length? And, what am I supposed to use to glue the inserts?

AKHunterNP 08-24-2011 11:36 PM

a high speed cutoff wheel. I use a cabelas 8000rpm arrow cutter but you can use a dremel, just make sure it's a straight cut. Don't try to cut straight through. Cut just far enough in and then rotate the arrow for a flush cut. Use AAE fastset or another type of arrow glue for the insert. You can use super glue but I would suggest the gel, not liquid because it can dry too quickly. I've seen some use liquid super glue and it dried so fast they didn't get the insert in all the way, it was glued in with about a 1/4 inch hanging out of the arrow.

Hooter56 08-25-2011 03:46 AM

Thanks brother. I had a good friend that lived in North Pole, AK about...holy crap, 18 years ago...damn I'm old.

bowtech86n 08-27-2011 02:00 PM

i have used a pipe cutter(copper pipe) on a dozen arrows and it seems to work fine for me so far. its a pretty clean cut. just slowly keep adjusting the pressure every couple turns.

SecondChance 08-27-2011 04:48 PM


Originally Posted by bowtech86n (Post 3839369)
i have used a pipe cutter(copper pipe) on a dozen arrows and it seems to work fine for me so far. its a pretty clean cut. just slowly keep adjusting the pressure every couple turns.

That will work OK on aluminium, but not on carbon. It will cause the fibers to split and crack, leading to a split/damaged arrow.

nodog 08-28-2011 03:41 AM

Judging by your second question your not to handy. If you were I'd say skip buying a designated saw that will just cut arrows and by something that is a multi use.

I'm a carpenter with many different saws and a good knowledge of blades and I use one of my miter saws with a fine toothed carbine tipped blade and a backer board that holds the arrow true and keeps the back of the arrow from any splintering (not needed but I do it just because that's always good). My saws are good enough to cut things way more difficult and expensive, they sure can cut an arrow. Just saying, buy something like that and use it for other things or sell it when your done.

Truthfully I don't think arrow saw are all that good of a saw and would never spend the money on one. A dremel will do it but I wouldn't use one of those either. When I do use one they create a lot of dust and carbon dust isn't good for you, beside you'd have to build a jig to cut them square. A pipe cutter I'd use if I was days away from civilization and needed an arrow to keep from starving. The wheel for starters is a wedge and a wall as thick as an arrow would be like cutting it with an axe.

The glue is per manufactures recommendations. On some I skip there talk and use super glue and quickly, don't try that with HIT insert. Not big on reading directions I take it. :)

The Rev 08-29-2011 07:57 AM


Originally Posted by bowtech86n (Post 3839369)
i have used a pipe cutter(copper pipe) on a dozen arrows and it seems to work fine for me so far. its a pretty clean cut. just slowly keep adjusting the pressure every couple turns.

You're very lucky you haven't had an arrow explode in your hand. NEVER cut an arrow with a pipe cutter! Ever!

Valentine 09-01-2011 07:19 AM

Passed on carbon arrows; once upon a time
 
I was nearly ready to move from aluminum to carbon. Except for one problem. I would have to give up my hand hack saw, inexpensive of course, for an electric archery saw, costing more than $100.

Of course, I stayed with aluminum or alloy as they are called now, and still have my hand hack saw. If I make the switch now, I'd still use an electric saw, but one from a building supply that can be used for other projects.

In fact, I still have a ceramic tile cutter, whose blade will make an excellent carbon arrow cutter.
But the aluminum arrows still shoot straight for me. The electric tile cutter blade is sitting ready in reserve. It's all paid for from household jobs; I'm cheap you know.

ijimmy 09-01-2011 08:20 AM

harbor freight has cut off saws cheep , around 20 bucks with a blade

nodog 09-01-2011 03:30 PM


Originally Posted by Valentine (Post 3841333)
I was nearly ready to move from aluminum to carbon. Except for one problem. I would have to give up my hand hack saw, inexpensive of course, for an electric archery saw, costing more than $100.

Of course, I stayed with aluminum or alloy as they are called now, and still have my hand hack saw. If I make the switch now, I'd still use an electric saw, but one from a building supply that can be used for other projects.

In fact, I still have a ceramic tile cutter, whose blade will make an excellent carbon arrow cutter.
But the aluminum arrows still shoot straight for me. The electric tile cutter blade is sitting ready in reserve. It's all paid for from household jobs; I'm cheap you know.

Tile saw would work good and with the water keep the dust down. The guide isn't all that great as tile depends greatly on grout covering a multitude of sin. Still, I think it would work very well. Have to give it a shot some day.


All times are GMT -8. The time now is 08:14 PM.


Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.