Limbs ( #'s )
 

Ok When i got my bow the limbs came on 60, or they where supposed to anyways, i turned them both down 1 full turn so i could get use to it, then planned on cranking it back up, well i was just wondering how do you know where your limbs areat their max? i am thinking its when they wont tighten anymor, just good and snug? well its hard already to loosen or tighten them, so just when they stop turning?

RE: Limbs ( #'s )
 

Limbs aren't necessarily at their max when the limb bolts are completely bottomed out (or all the way in). You can tweak a bow to get a few more lbs out of it by twisting the cables.

RE: Limbs ( #'s )
 

AS MY BOW IS, with the bolts tightened all the way i'll be at max tho wont i

RE: Limbs ( #'s )
 

Bolt all the way in does not mean the limbs are maxed out.

It just means the bolts are maxed out.

RE: Limbs ( #'s )
 

ok well when will the limbs be maxed out? or do u have to play with them to know, seems like to me if the bolts are all the way in the limbs are gonna be maxed? i really dont understand

RE: Limbs ( #'s )
 

Maxed out limbs are when your bow is in tune, the bolts are all the way in and the cables have the maximum twists on them.

See, you can twist your limb bolts all the way in and your bow limbs will still have more flex in reserve. Thus they are not maxed out. Getting this additional reserve by twisting the cable and having your bow in tune will make your limbs maxed out.

RE: Limbs ( #'s )
 

Example: Diving Board

A diving board is attached to the pool side by 2 bolts and 2 springs.

The directions from the manufacturer state that the maximum capacity of the diving board is 300lbs.

Through testing you have found that by tightening thebolts all the way down so the springs collapse, the diving board can at least hold 350lbs.

This additional 50lbs is the reserve.

Setting up for a 350lb diver makes this board maxed out. Much like bow limbs when the reserve has been accounted for.

RE: Limbs ( #'s )
 

Your limbs are maxed when the draw weight checks out at the maximum weight they are rated for. Period.

You CAN get more out of them by twisting the string and cables up to put more preload on the limbs, but that's not really smart. By doing that you put the limbs under excess strain which reduces their service life. You also increase the brace height *** although I must admit I do not know if it works that way for parallel limb bows. Maybe someone who knows can chime in and educate me on that?*** Anyway, raising brace height reduces the bow's power stroke and pretty much erases any speed or energy benefit from overloading the limbs by a couple of pounds.

I like to set up my bows so that I hit peak weight with my limb bolts a full turn from bottomed out. That gives me some cushion to work with in order to fine tune my tiller. Getting the tiller just right is FAR more important than a measely 2-3 extra pounds of draw weight.

RE: Limbs ( #'s )
 

Bows are designed to optimally shoot a particular arrow at a particular draw weight. Arbitrarily increasing or decreasing draw weight is not a good idea, especially when shooting broadheads. You want the draw weight set to match the dynamic spine of your arrows. If it exceeds the maximum draw weight rating of your limbs, then you need to add tip weight to get more flex on the arrow. You could probably force a 60 lb limb to draw at 70 or 75 lbs, but why would you want to risk injury and a busted bow for that?

RE: Limbs ( #'s )
 

Lol, i never said anything about taking the weight over 60 pounds, and i do not want to, by maxed out i meant 60 pounds

RE: Limbs ( #'s )
 

From what I understand, all limbs come as a pair. Each limb is tested and paired with another limb that testthe same. Just because your bow says it is a 60lb bow does not mean the limbs at maxed at 60. They may test one limb to be 63 and then pair it with another limb that test a max of 63. If you want your bow to be at 60lbs, the only way to be sure is totestit on a scale. Just because your bolts are bottomed out doesn't mean the bow is at sixty. It can be more or less. If it is less, then your string and cables are the correct length. They need to be replace or twisted more.

I am no expert, but I read and listen to everything I can on archery and tuning. If I made a mistake, I am sure someone will correct me.

RE: Limbs ( #'s )
 

Yes,when your limb bolts are tightened all the way down your at your max draw weight,which may be 2 to 3lbs over the stated draw weight on your bow.IE your 60 lb bow with the limb bolts tightenedall the way mayactually max out at 63lbs.Forget the cable and string twisting this will only cause you more headache, by altering your draw lenght,brace height ect.I hope that answers your question.

RE: Limbs ( #'s )
 

When they bolts are the are tight you are at max. You can be above or below the 60# rating that is listed for that bow. Typically, the bow is over. My bow is rated at 70# but when bottomed out is at 75#.

If you are below then you can add twists to the string to get the bow to 60#'s without necessarily changing any of the other characteristics if the string/cables have stretched a little due to shooting. You can check your ATA and it will tell you if you need to add twists.

RE: Limbs ( #'s )
 

Call the factory that made your stick slinger and ask for higher buttons or find out what the deflexion is on your limbs and order a stronger set.

If you go twisting the cables and strings make sure your proshop does it right and doesnt go more than 2 or 3 twists. Thats when a bow can detonate on you and give you stitches, I know from experience.

RE: Limbs ( #'s )
 

i dont want higher limbs, i got 50 - 60 because thats what i want, not to go higher than 60 or buy higher # limbs, some of these answers arent answering my question really, but i got my question answered by some(dave), thank you

RE: Limbs ( #'s )
 

I think adding taller buttons would void your warranty.The bow came with the ones that are there for a reason.

RE: Limbs ( #'s )
 

I ordered mine from the factory and it didnt void the warrenty.