how to get broadheads to group with my field points
 

I shoot a high country brute force 73 lb pull 28.5 inch goldtip 7595 with 5 inch helical vanes.the broadheads are thunderheads and rocky mountain iron heads both 100 gr neither one will group close to my field points .they group about 2 inches to the right at 20 yds and about 6 inches to the right at 40 yds i know this is acting as a weak spine but the 7595 is a plenty enough stiff shaft.I have moved my arrow rest to the left and it helped a little but it made my field points hit to the left a little more.i have lowered my draw weight but it did not seem to help.My bow has been properly paper tuned.I just wonder if anyone else has any suggestions to fix this problem.I am interested in any names of some good fixed blade broadheads that fly like field points.

RE: how to get broadheads to group with my field points
 

I had good reults with magnus stingers4 blade.

In general any two blade will be easier to tune than a 3 or 4 blade.

the smaller 7/8 inch to 1 inch cut 0nes will be easier to tune than the larger1 3/16 inchones.

www.eastonarchery.comdownload tuning guide and it will give you some more options for your problem

RE: how to get broadheads to group with my field points
 

4 words BOW OUT OF TUNE

RE: how to get broadheads to group with my field points
 

www.broadheadtests.com

RE: how to get broadheads to group with my field points
 

How about arrows out of tune? Sounds like your inserts aren't lined up correctly.

RE: how to get broadheads to group with my field points
 

Easton's Tuning Guide. Check it out. http://www.eastonarchery.com/downloads/pdfs/tuning_guide.zip

RE: how to get broadheads to group with my field points
 

http://www.broadheadtests.com/TUNING.html

RE: how to get broadheads to group with my field points
 

I would start by paper tuning. It will likely point out some flaw. Then try slick tricks.

RE: how to get broadheads to group with my field points
 

I just shoot NAP Spitfires, they fly the same as field points.

RE: how to get broadheads to group with my field points
 

Search ..u will find tones of info.

Buy some slick tricks, if they don't shoot your bow is out of tune.

Try bare shaft tuning, play with rest , and knock point.

RE: how to get broadheads to group with my field points
 

i remember a time that i had the same problem what i did was to take all the different arrows that i had and cut them to the same length these included 2219,2216,2117,2115,2114,2018,2016, 1916.even tryed carbens 4560 and i shoot 70# all but one arrow would go to the right and that arrow is not the one the chart even listed for that much poundage.what you have to do is try different things find out what works for you.rite now i shoot a mathews switchback 70# 26.5 .1916 with 4in vanes ,wasp camlock 100 and a laydown rest (dont know what one it is but it caust $109.its a good one) my old bow was a mathews fx ,it had a bowdotle rest ,arrows were 27in 1916 ,i did try carben 4560 but that right thing washappeningagine sofor hunting i just stay with the 1916s

RE: how to get broadheads to group with my field points
 

Arrows shooting right usually does indicate a weak spine. Does anybody actually read Easton's Tuning Guide? Read the last paragraph on page 7. It says that sometimes release shooters get an opposite indication than those commonly achieved. I'm gonna bet that your arrows are acting too stiff. A quick way to find out is, if you can, just turn the weight of the bow up one full turn and see if that helps the situation. If it gets worse then turn them down from the original setting. Limb bolts are put ona bow to help with the tuning process, not just set the weight of the bow. There is nothing says you HAVE to shoot a particular weight. Where the bow tunes is where you shoot it. Simple as that. And anything over 50 lbs a deer doesn't really care.

RE: how to get broadheads to group with my field points
 

NAP razorbacks

Learn it, live it, love it.

RE: how to get broadheads to group with my field points
 

What type of fletch is on your arrow , I like 3-5" feathers on an offset or 4-4inch feathers on an offset to stear fixed broadheads . The precieved standard of 3-4" vanes on an offset , just does not have enough stearing effect for fixed heads IMO . You can waste some serious time trying to tune your setup and arrows , but if you dont have enough stearing in the rear of the arrow to counteract the stearing in the front[broadhead] , it like pounding your head against the wall , when the answer is simple .