HuntingNet.com Forums - Search Results
HuntingNet.com Forums

Go Back  HuntingNet.com Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Search: Posts Made By: Colorado Cajun
Showing results 1 to 18 of 18
Search took 0.02 seconds.
Forum: Gunsmithing
12-29-2010, 03:04 PM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

The little I played with the chrono on Sunday, I...

The little I played with the chrono on Sunday, I can see where it will be a valuable tool. LOL! He will never live that one down, which he shouldn't.
Forum: Gunsmithing
12-29-2010, 07:14 AM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

Well, I took her out shooting on Sunday and I'm...

Well, I took her out shooting on Sunday and I'm happy. I didn't get to shoot it as much as I would have liked. My main priority for the trip was to let my daughter shoot her new Henry. She was all...
Forum: Gunsmithing
12-23-2010, 08:32 AM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

It must be a Remington thing because I just...

It must be a Remington thing because I just bought the pin from Brownells. Merry Christmas everyone.
Forum: Gunsmithing
12-22-2010, 12:46 PM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

Thinking about it after my last post, I think I'm...

Thinking about it after my last post, I think I'm going to measure the pin with my calipers, buy round stock and make my own pin. I may even blue it.
Forum: Gunsmithing
12-22-2010, 11:57 AM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

I got it all put back together and can't wait to...

I got it all put back together and can't wait to shoot it. Probably Monday when I take my daughter out to shoot her Henry 22 lever action that Santa is bringing. :) While I had it stripped down I...
Forum: Gunsmithing
12-19-2010, 01:40 PM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

I got the tape out without having to use any...

I got the tape out without having to use any tools, other then a needle and a very small screwdrive. I put a LITTLE water in the pocket and let it sit for 5 minutes. That made a huge difference. I...
Forum: Gunsmithing
12-19-2010, 09:16 AM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

I had covered the front, sides, and bottom of the...

I had covered the front, sides, and bottom of the recoil lug with two layers of tape to give me a little room as suggested in the instructions and by others. The little extra room in front and to the...
Forum: Gunsmithing
12-19-2010, 06:51 AM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

Alright! I'm really happy over all with the job....

Alright! I'm really happy over all with the job. The only spot I had any problems is on the tang. The glob that sat under the lug came up when I pulled the barrel off. I was worried about the chamber...
Forum: Gunsmithing
12-19-2010, 06:43 AM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

Good deal and congratulations to your friend.

Good deal and congratulations to your friend.
Forum: Gunsmithing
12-18-2010, 12:49 PM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

The wait has begun!!!! I'm feeling pretty good...

The wait has begun!!!! I'm feeling pretty good about it but the truth will come in the morning when I pull the barrel off. I've always been one to listen to other people experiences and learn from...
Forum: Gunsmithing
12-18-2010, 09:17 AM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

So, I should fill that hollow part in under the...

So, I should fill that hollow part in under the 1st two inches and not do just the upper side edges where the barrel used to meet?

I put 3 coats of release agent on the barrel. I'm going to give...
Forum: Gunsmithing
12-18-2010, 07:50 AM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

Alright! I think the stock is ready to go. What...

Alright! I think the stock is ready to go. What do you think?

http://img811.imageshack.us/img811/2115/dscf0041k.jpg (http://img811.imageshack.us/i/dscf0041k.jpg/)
Uploaded with ImageShack.us...
Forum: Gunsmithing
12-17-2010, 05:18 PM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

Thank you Big Uncle and Pawildman!!! I understand...

Thank you Big Uncle and Pawildman!!! I understand now. Tomorrow I will remove the tape and prep that part until the end of the chamber and bed it too. I'll probably actually do the bedding tomorrow....
Forum: Gunsmithing
12-17-2010, 01:02 PM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

I'm thinking after reading this that I may not be...

I'm thinking after reading this that I may not be uderstanding what exactly should be bedded in the barrel section. I'm thinking of filling in the hollowed section of the barrel channel without it...
Forum: Gunsmithing
12-17-2010, 11:47 AM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

The tape in the barrel channel is there for...

The tape in the barrel channel is there for cleanup just incase I make a mess. You can't see it on the barrel in the pictures but I do have have several wraps on the barrel to give it a float. I did...
Forum: Gunsmithing
12-17-2010, 07:44 AM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

Here is an update. Got some sanding done and...

Here is an update. Got some sanding done and removed a lot of material around the recoil lug. I also took it down around the tang and front stock screw to build those are up with glass for more...
Forum: Gunsmithing
12-17-2010, 07:25 AM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

These are before pictures, without any sanding or...

These are before pictures, without any sanding or grinding. I'll post some more soon of the sanded, grinded stock. After reading the instructions that came with the kit, it said to drill some small...
Forum: Gunsmithing
12-15-2010, 09:05 PM
Replies: 46
Views: 6,145
Posted By Colorado Cajun

Bedding the stock on my 700ADL

I started a thread under the gun section about new stocks and then later decided bed the factory stock in stead.
http://www.huntingnet.com/forum/guns/335855-new-stock-rem-700-3006-a.html

I...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.