|
Question on pillar bedding
I can see pillar bedding an action where the magazine is attached to the receiver (like a 700 ADL). If you have a detachable magazine (like an A-Bolt) , when you raise the receiver/barrel, will the cartridges still line up and feed correctly?
|
RE: Question on pillar bedding
When you pillar bed an action the pillars are typically left long and then machined down on a mill to the correct height after they have been epoxied in place.
|
RE: Question on pillar bedding
Thanks. I had read an article about pillar bedding along with free floating the barrel and in the pictures, it looked like the action was raised a little. They wrapped a couple of wraps of electrical tape around the action and the barrel before seating it in the epoxy.
|
RE: Question on pillar bedding
That's the cheap, cheasey and easy way to do it and usually results in less than appealing visual asthetics.
To do it properly you should, if you do not have access to a mill, measure everything perfectly and exactly the thickness of the wood between the bottom metal and receiver. Once you have done that you need to drill out the action screw holes about ten thousandths over the size of your pillar. Screw the pillars to the receiver useing your action screws. Use modeling clay to plug up any holes and crevices that you do not want bedding compound to get into. Wax the receiver and the very bottom of the pillars and action screws, and also the inletting for the bottom metal (furniture wax will keep the bedding compound from sticking to it). Tape up the rest fo the wood with masking tape. Useing your favorite bedding compound cote the inside of your holes and cote the pillars also. Insert the receiver with the pillars attached into the holes and clamp the receiver in place with bar clamps (protect the wood with something so you do not dent it). Wipe off any excess and allow to dry for 24 hours. |
RE: Question on pillar bedding
Is there a gunsmith you would recommend to do these things? I'd even ship out if it's not local to me. I'd also like to know more on lapping the rings, etc. as these are all things that I have read about and seem to make a marked difference for the better. Any advice?
Thanks! ORIGINAL: bigbulls That's the cheap, cheasey and easy way to do it and usually results in less than appealing visual asthetics. To do it properly you should, if you do not have access to a mill, measure everything perfectly and exactly the thickness of the wood between the bottom metal and receiver. Once you have done that you need to drill out the action screw holes about ten thousandths over the size of your pillar. Screw the pillars to the receiver useing your action screws. Use modeling clay to plug up any holes and crevices that you do not want bedding compound to get into. Wax the receiver and the very bottom of the pillars and action screws, and also the inletting for the bottom metal (furniture wax will keep the bedding compound from sticking to it). Tape up the rest fo the wood with masking tape. Useing your favorite bedding compound cote the inside of your holes and cote the pillars also. Insert the receiver with the pillars attached into the holes and clamp the receiver in place with bar clamps (protect the wood with something so you do not dent it). Wipe off any excess and allow to dry for 24 hours. |
RE: Question on pillar bedding
I would reccomend myself but I am not set up to do it properly yet. I would not want to attempt it unless I could do it right.
Hopefully within this next year I will be able to do just about anything one should need. I did know of a couple of people in Denver but they have since sold and moved to companies such as Nesica Bay. I'd also like to know more on lapping the rings, |
RE: Question on pillar bedding
Excellent! Tell me when your shop is setup and I'll send my baby away ASAP. :-)
My apologies, I was not specific, dolt that I am sometimes... I meant lapping the rings for the scope. I believe I read that this is good to do to remove pressure(s) on the scope when mounting it. I'll try to find the link where I read this. |
RE: Question on pillar bedding
|
| All times are GMT -8. The time now is 12:39 PM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.