Remington model 700 & Factory ammo (7mm mag)
If anyone can point me in a direction for picking a factory round that shoots well in this combo, that would be appreciated. It's not going to be a gun that gets shot enough for me to get dies & components to work up a hand load. Probably looking to shoot 150-160 gr bullets, willing to look at most any hunting bullet. Premium or mid grade, as long as it shoots I'll be happy.
|
Originally Posted by rybohunter
(Post 3586440)
If anyone can point me in a direction for picking a factory round that shoots well in this combo, that would be appreciated. It's not going to be a gun that gets shot enough for me to get dies & components to work up a hand load. Probably looking to shoot 150-160 gr bullets, willing to look at most any hunting bullet. Premium or mid grade, as long as it shoots I'll be happy.
It may cost a bit to experiment with various brands/specs ammo to find the best performer in your particular gun, but that is generally how it has to be done.... |
Buy several different loads and see what your gun likes best, there is no way anyone can tell you that.
|
Originally Posted by thndrchiken
(Post 3586561)
Buy several different loads and see what your gun likes best, there is no way anyone can tell you that.
|
after just recently starting to handload, im surprised you dont wanna hand load for it...
though i know you like to hunt with your bow and handguns and such and likely wont pick up the 7mag much... dies, brass, a pound of powder, some brass, and a box of good bullets and your ready to go...you might not find a load that cuts serious holes with 1 powder and 1 bullet...but, you will most likely match factory ammo accuracy pretty easily...and likely exceed factory results if you tinker with charges a bit... i just tested 7 different charges in my 35 whelen i just got...same powder..same bullet..out of that, i had 4 charges shot 1.5" or less and one was .75"... and 7mag ammo aint cheap...not tryin to talk you into handloading..but if you already have the rest of the stuff, dies and components will last you forever and you'll save a ton...3 boxes of shells will run you over the cost of dies and components i bet... factory ammo, my mauser really liked Hornady...and ive shot ALOT of different ammo through it..from cheap stuff to high end winchester, federal, hornady etc... |
All the reloading components would cost me WELL over a box of shells, probably 2-3. Add on the time to mess around with it, to me it's just not worth it for a gun that in all honestly may never even get shot at a critter. I've seen numerous times where several guys have had one load shoot well out of a particular model. I guess this isn't one of them.
|
I've ran all sorts of stuff through my 7 and friends' 7s. They all shoot fair...from Wolf to Winchester Supreme, though mine hasn't had a factory dose through it. I gun 120gr SPs through mine at modest speeds and deer don't like 'em, nor do they care for anything else from the 7. Pick one....
|
I have found that my 7mm RM shoots everything good (around 1 inch)...my go to rounds are Winchester's Supreme 150 grain BST (0.5 inches from my rifle) and Federal Supreme 160 grain Nosler Partitions (0.70 inches from my rifle).
In truth, I have shot... Winchester powerpoint, silvertip and BSTs, Remington Core-lokt, Managed Recoil, Federal Hi-shok, Nosler partition, Ballistic tips, etc...all reasonably well. Longest shot I took on a deer was 285 yards with Remington Core-lokt...1 shot: dead deer. You need to try several types to find out what your gun likes and what you are comfortable with. |
I have had good luck with Federal Premium ammo shooting well in my rifles.
I recommend Federal Premium loaded with 160 grain Nolser Partition bullets. |
My Remington 700 7mm Mag is a tack driver with 150gr Remmy CoreLokt's.
Keep in mind that I have a $500 scope on it too and not some cheapo. |
All times are GMT -8. The time now is 06:27 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.