My new 7600 7mm-08 (Pics)
 

Here are a few pics of my new Rem 7600 7mm-08.





I put a Burris 3-9x40 w/Ballistic Plex reticle on as that's the same scope I've got on my Rem Mtn LSS. The rings are Leupold Quick Release. I've got a 6.5-20X50 scope that I use for range work and with the Lupey QRW rings I can switch the range scope to eigher the 7600 or my Rem Mtn LSS as needed.

Today I'm working up some 154 Hdy RN loads to try out in the 7600 and hope to get to the range this afternoon. I'm just looking for minute of Whitetail accuracy at this point as I plan to hunt the last two days of Missouri rifle doe only season next weekend.

I'm keeping my fingers crossed that this rifle will shoot as well as my Mtn LSS

firstshot
---------------------------------
Make your first shot count!

RE: My new 7600 7mm-08 (Pics)
 

Thats a sharp looking rifle. Those remington pumps are reliable and if my limited experience counts often as accurate as many off the shelf bolt rifles.

Good luck next weekend

RE: My new 7600 7mm-08 (Pics)
 

Remington started offering the 7400 in 7mm-08? Cool!!!!

RE: My new 7600 7mm-08 (Pics)
 

Ahhhh shes a beaut first!!! Be sure and give a range report on those 154's. Good luck on them show-me does!!!

RE: My new 7600 7mm-08 (Pics)
 

No...not yet. This is a Grice 7600 special run. http://www.gricewholesale.com/specials_7600.php

firstshot
----------------------------
Make your first shot count!

RE: My new 7600 7mm-08 (Pics)
 

NoKnees / Doe Dumber

Thanks guys!!

I think she's a looker too....but hopefully I'll find out this afternoon if she's "all show and no go". Don't have time to find a load she really likes but I should at least get an indicator of if she's got potential or not. The 154 Hdy RN's shoot sub MOA in my Mtn LSS. Working against the clock to get some loaded up....hope I'll have time to get out there this afternoon. If so, I'll post a range report.

firstshot
-----------------------------------
Make your first shot count!

RE: My new 7600 7mm-08 (Pics)
 

nice looking gun - congrats

RE: My new 7600 7mm-08 (Pics)
 

I have a 30-06 Carbine pump. I have had it for almost 30 years. You have a fine rifle there sir. They will shoot well, but I believe they are a little more finicky than a bolt rifle. I have had more accuracy over the years with faster powder, and larger bullets. The pump is a popular rifle here in WV. We all have one. Just one question, it is hard to tell by the pictures, but is that scope a little high? Tom.

RE: My new 7600 7mm-08 (Pics)
 

Tom

Someof it is the angle of the picture, but yes,the scopeis just a tad high. I've got Leupold quick relase rings on there as I wanted theoption to be able to remove the scope and use the iron sights. As you can see in the 3rd pic, the iron sights sit kind of high so I set the scope up just a little higher than I normally would so I would not be able to see the iron sights through the scope.

Even though it looks a bit high, when I bring the gun to shoulder, I've got a good cheek weld an a perfect sight picture with them set that way.

firstshot
------------------------------
Make your first shot count!

RE: My new 7600 7mm-08 (Pics)
 

It almost looks like you took that gun from my safe. I have one too and i love it.

RE: My new 7600 7mm-08 (Pics)
 

Thats a sharp looking rifle.I passed on a birch stocked Rem 7600 in 25-06 a year ago.I'm now wishing I hadn't.
BBJ

RE: My new 7600 7mm-08 (Pics)
 

O really hope they make the 7mm-08 in a pump as a regular offer.

I noticed a cool looking pump-action in .223 on that website. I didn't know Remington makes those kinds of guns.

RE: My new 7600 7mm-08 (Pics)
 

Younggun243

That is a cool looking 223 Grice is offereing. Bet it would make an outstanding coyote/varment rig, especially with the AR style magazine...you could load a 30 round mag in there...LOL

firstshot
----------------------------
Make your first shot count!

RE: My new 7600 7mm-08 (Pics)
 

Wimuzzleman

How about a little more info on your 7600? How has it performed in the hunting woods? Do you reload for it? Please share best loads, be it handloads or factory. What kind of muzzle velocities are you getting? What kind of groups?

Thanks
firstshot
-------------------------------
Make your first shot count!

RE: My new 7600 7mm-08 (Pics)
 

I left the rifle sights on my carbine. You are right, they are a bit high. I put a mark on mine where they are sighted in, then I moved them down the rail so that they would not catch on any thing. Are your bases Weaver style? Mine are on my other pump. I took the back sight off that rifle. I have a peep sight made be NECG that mounts right on the Weaver base when I remove the scope. It is very low profile. Also I have never noticed the back sight on my scopes.

I think it is important to have a low profileon fast action, woods rifles. In woods conditions I sight my rifle dead on at 100, and the closer to the bore, the tighter the trajectory. I feel more confident when my crosshairs are real close totree limbs. IMO. Tom.

RE: My new 7600 7mm-08 (Pics)
 

Tom

I put Weaver style bases on the 7600. I have Leupold quick release bases and rings on my Mtn LSS and wanted to be able to interchange scopes between the two rifles. As you probably know, the quick release rings have a cross bar that matches up with a slot in the bases so you can return the scope to the exact same position when you remount it. I tried Leupold quick release bases on the 7600 but with, the the slots were in a different place than those mounted on the Mtn LSS. Then tried the weaver bases and wouldn't you know it, the slots matched up exactly to where the Leupold slots were on the Mtn LSS.

I've got a 6.5-20X50 scope that I use for range work and could switch this scope with the 3-9x40 on the Mtn LSS as needed. Now, I can use the 6.5-20 on either the Mtn Lss or the 7600.

Thanks for the tip on the NECG peep sight that fits the weaver bases!!!! Although I had not done any serious searching yet, I definitely had it in the back of my mind to try and find a peep sight setup that I could use on the 7600. The NECG that mounts on the Weaver bases is perfect!!! With that, I'll be able to use the peep, the 3-9 scope or the 6.5-20 scope as the situation dictates.....outstanding!!!!!

Thanks a bunch!!!!!!

Doug
(firstshot)
-----------------------------
Make your first shot count!

RE: My new 7600 7mm-08 (Pics)
 

Tom

One more thing. I assume the big thumb knob on the left is for attaching to the weaver bases. The NECG website says these are adjustable for windage. Just wondering, how you do that?



firstshot
-------------------------------
Make your first shot count!

RE: My new 7600 7mm-08 (Pics)
 

The large kob on left is used to tighten the sight to the base. If you look real close at lower left hand corner you will see an adjustment screw. Also the aperture can be unscrewed-and different aperatures can be used. Also loosening the aperture allows you to set elevation. I prefer to leave rear sights centered, and make slight windage adjustments with the front bead-so I have never adjusted mine for windage. But if they say it is so, then it is so. The Quality is second to none. The only problem you might have is with front sight height. If you order from NECG it may cost a couple of extra bucks, but they can calculate front bead height for you. Tom.

RE: My new 7600 7mm-08 (Pics)
 

I have this same rifle. Just got it late last month thru Grice. I believe it was one of the last ones available. Very sharp, and an excellent addition to the gun locker. Have yet to shoot it, hopefully this weekend, and will take any tips or suggestions in relation to factory loads for the 7-08. I deer hunt West Central WI, in hardwoods and my longest shots in the last 8 years have been 85 yards or less. I don't reload so if anyone's got any suggestions, feel free to pass them along. I try to lean towards Hornady or Federal Premium in all my other guns.
Thanks in advance.

RE: My new 7600 7mm-08 (Pics)
 

Canned Heat

Sorry...can't help with the factory loads. The only ones I've tried in my rifle were Federal Fusions (I think 140 grn)and the best groups I could get were in the 1 1/2 - 1 3/4" range at 100 Yds.

Only reason I tried them at all is I had just moved to Texas and didn't have my reloading equipment with me. I'll definitely stick to my reloads which are averaging 3/4"-1" consistently & get some 1/2" inchers on a good day.

firstshot
--------------------------
Make your first shot count!

RE: My new 7600 7mm-08 (Pics)
 

Thanks anyway Firstshot...

I'm playin' hell trying to find Federal Premium Barnes TSX's in 7mm-08 up here. They offer the damn things but nobody stocks 'em. Anyone that I know around here that reloads onlyworks withtheir trap & skeet loads. The sad part is...I'm 1 mile from a Sportsman's Warehouse, 8 miles from a Cabela's, and 12.5 miles from a Gander Mountain. Looks like Core-Lokts, Fusions, Winchester BST's, or Hornady SST's.

RE: My new 7600 7mm-08 (Pics)
 

I shoot a 760 in .30-06 that is older than I am. You're going to love that rifle.

BTW, ATI makes a few different stocks for it, if you want to switch them out to keep yours looking nice.