Some 28ga FH info and ideas.
Brenneke now has 28ga slugs, with good speed,
decent smooth bore accuracy. About 260 grain
slugs. SAme style as their 12ga ones with locked
on base.Work in 28ga NEFs of course and
28ga O/Us.Some real good 28ga O/Us out there.
28ga is a .550 Inch bore.

But now Rossi has out, a revolving 28ga shotgun
with about a 19 inch barrel. Should work ok with
those slugs. You could also get RMC 28ga brass cases
about 2 3/4" long, maybe 3", depending on chamber,
a shorter version of our 28GA FH 3.25" case.

Maybe I get one in the future, and put on a longer
heavier 585 cal barrel and set it up for my
585 Short HE. Have a switch barrel 28ga/585.
Neat gun.Called Circuit Judge....Ed

I found a picture of 28ga Rossi Circuit Judge. Barrel is
smooth bore , could be little heavier barrel, but it will do
ok with the new plastic case Brenneke slugs,
260 gr at 1450 fps..Could do 2000 in a little longer
brass case from RMC.

28ga is a 550" bore in a rifled bore.
24ga is about .585 same bore as my 585, and
most all 577/585 stuff. The 28ga chamber with minimum work
would fire my shorter 585 with a switch barrel 585 bore.
And still work with 28ga with 28ga barrel put on.
Difference is the case thickness with the 28ga case
being nearly the same OD as my 585 drawn, stronger
brass cases.

The Brenneke slug has along locked on base and seal,
connected by long post, that you can see inside
the case in picture and pictured on the box
Quite a long tail so to speak for
good smooth bore work.This is a great step forward
for 28ga slugs, as most reloading slug stuff was only
100 grain balls or other super light slug designs...ED

Some have a need for supply of full bore 12ga hard alloy
slugs about 620-650gr. So a couple guys are opening up
their Lee Key Slug molds to full bore .729" It will still
have the partly hollow base and key. I will do the
short brass cases with the first ones I get, to get loads
developed. The slugs are about same length as
the 730 gr Dixies.They have blunt round nose and
can be roll crimped in plastic cases ok. Load of 90gr
of IMR4759 in the short brass or 3" plastic cases
will get 1800 plus in 24" barrels.
I'll Have pictures later to post.

Also here is picture of my 585HE in a Khan
shotgun action. Operates as a straight bolt,
straight pull action for now. Barrel is heavy,
30" long, the butt is weighted. thick pads,
it fits nice, looks great. Ed

need good weather,

awesome
 

cool idea, I guess your covered if a graboid breaks into your rec room!! reminds me of the old 8 bore guns the ivory hunters had

10ga FH ideas..Ok I think the most stylish guns in the world
are nicely built over/unders. And there is a heavy duty
10ga over under made by Armi San Marco, imported by
Cape Outfitters. That is one brand I've lately
seen some sold on GB. Others just as strong are Armsport
shown in the picture below, also
American Arms, and Richland Arms.
And probably a few more.

I'll be trying to get one I can afford, I could
ream one chamber for 4.05 brass case
for slugs, and leave other for 3.5" magnum shot and slug
loads in plastic cases. But if we left both 3.5" you'd
still have a hairy gun. You can buy 3.5" new plastic cases,
with hot Fed 239 primers for 22 cents each.
Make a real great combo gun.For slugs with
the right weight slugs.Don't go real heavy.

For slugs use the hollow base hard cast lead
900gr in brass case, at 1900 fps,that the
guy in AZ makes.In plastic about 1750.
Those are not a full bore loads,needing real thick
barrel, but that heavy O/U has barrels ok for that,
keeping pressures at mag shotshell levels.14,000 psi.

These modern O/U actions can take pressures like the
heavy duty NEF SB2 10-12ga frame, if barrels were thick
enough.20,000 in 10ga. IE the actions are real strong.
Ruger has made O/U rifles on their O/U frames,
and others have made big bore rifles
using modern over/unders. I like idea of O/U
double ten slug gun knowing the speed we have
gotten with our slow powder slug loads....Ed

Some newer slug ideas coming around. First is Brenneke,
a locked on base ounce slug in sabot at factory speed of
16-1700 or so in 3" plastic.Really go in our 3.5" loads.

Second is Federal Deep Penetrator, 1 oz, copper plated
and a harder lead alloy, than Federals regular slugs.

Third is Dupleks, steel slug riding on a plastic band,
penetrates very well. About 1 1/8 oz.

Seeing the slug base attached deal from Brenneke,
in a sabot I figured out the following.
The idea is the new BPI blue sabot, being undersize for
12ga, is a perfect fit in a 10ga bpi wadcup, The blue has no
cushion on it so it sits in cup ok and a roll crimp works.
Just shaved bottom edge corner and fits bottom ok.
In 32" heavy barrel NEF 10ga, and 10ga 3.5" plastic case,
gets over 2300 at less than mag shotgun pressures
with 440gr slug in blue sabot.I plan on in future to
make a 10ga with rifled barrel, which these would be best in.

If I can find thin wall 10ga wadcup the 12ga bpi AQ slug
would work even better, as it is for smooth bores....Ed

Yesterday was the 5 1/2 anniversary of this post.

In that time:

14,319 members have gotten divorced.
213 members have come out of the closet.
4,498 members have threatened to leave and not come back.
AND...17 cartridges have become obsolete.

That's pretty impressive.

That is a fun message you posted.....
And also we have helped quite a few around the net.
Some of the real big sites have 2-3 times the views,
and one huge one has about 50 times the views.
The experimenting and shooting are a great hobby,
and if the nutty anti-gunners don't take it all away,
and we hope to be doing this for a long time..Ed

Nothing against you in my post, ED....I read this all the time. It just struck me as funny that this has been around so long.

Keep it up.