Go Back  HuntingNet.com Forums > Firearms Forum > Black Powder
 Problem with Thomson center >

Problem with Thomson center

Black Powder Ask opinions of other hunters on new technology, gear, and the methods of blackpowder hunting.

Problem with Thomson center

Old 02-13-2004, 05:34 PM
  #1  
Fork Horn
Thread Starter
 
Join Date: Dec 2003
Location: Wisconsin
Posts: 287
Default Problem with Thomson center

Hi guys,

A friend of mine has a Thompson center Renegade that has some cleaning items stuck down the barrel. He is not sure if the breech plug is removable or what may be the best method to clear this out. It is also quite possible that there may be a load still in the barrel, it is unknown.

I shoot a Knight and just unscrew the breech plug, but I'm not familiar with this rifle. Any ideas??

Thanks,
Cybersniper
cybersniper is offline  
Old 02-13-2004, 06:27 PM
  #2  
Nontypical Buck
 
Join Date: Jul 2003
Posts: 2,922
Default RE: Problem with Thomson center

Sorry cybersniper

We would have to know EXACTLY what is lodged in the barrel to help remove it. We have no lights or tools at our disposal here.

I suggest your friend soak the bore with water -- close the hammer onto a tire valve cap over the nipple -- encase the rifle and take it to a gunsmith. Don't take any chances... especially metal to metal screw-in if powder & bullet may be present. Better safe than sorry.. it won't cost much to have the clog removed.
Triple Se7en is offline  
Old 02-13-2004, 06:42 PM
  #3  
Fork Horn
Thread Starter
 
Join Date: Dec 2003
Location: Wisconsin
Posts: 287
Default RE: Problem with Thomson center

It appears to be a cleaning jag and some patches.
cybersniper is offline  
Old 02-13-2004, 06:42 PM
  #4  
Fork Horn
Thread Starter
 
Join Date: Dec 2003
Location: Wisconsin
Posts: 287
Default RE: Problem with Thomson center

Is the breech plug removable?

Thanks
cybersniper is offline  
Old 02-13-2004, 07:12 PM
  #5  
Nontypical Buck
 
Join Date: Feb 2003
Location: Kerrville, Tx. USA
Posts: 2,722
Default RE: Problem with Thomson center

NO, it is not. I own a Renagade. He is going to have to try and get it out the front
txhunter58 is offline  
Old 02-13-2004, 07:48 PM
  #6  
Dominant Buck
 
cayugad's Avatar
 
Join Date: Feb 2003
Location: Wisconsin
Posts: 21,193
Default RE: Problem with Thomson center

If there is a possibility of a load being in the rifle he has a couple of choices. He can soak the barrel with water to kill the charge, and then take it to a gunsmith.

The other thing he might want to try is a Co2 charge remover. Many times that might be able to blow the thing out of the barrel and the charge if there is one. I would still water the barrel and make sure the charge is killed before I use the Co2 remover.

The other thing I have heard of people doing is rigging a nipple to a air compressor and then with a lot of air pressure built up, blow the barrel clean that way. Again, if it might be loaded water the charge. Never take a chance with a charge in the barrel. It does not take much to set them off and in his case it would be in a dangerous situation....
cayugad is offline  
Old 02-13-2004, 08:03 PM
  #7  
Typical Buck
 
Big Guy01's Avatar
 
Join Date: Nov 2003
Location: Southampton, Ontario, Canada
Posts: 974
Default RE: Problem with Thomson center

After making sure there is no charge or that the charge has been soaked to de activate the powder I would try the Co2 discharger . If this doesnt work pour some "Liquid Draino" down the barrel and leave it set for a couple of hours. This should dissolve the cleaning cloth and you should be able to tap the muzzle on a table and the jag should fall out. The draino won't hurt the steel, but it will eat up any thing organic like skin, wood and varnish. Be extremely carefull you dont get it in your eyes. I would not try the Co2 after I put draino down as if it blows free it could spray in your eyes.
Big Guy01 is offline  
Old 02-13-2004, 08:06 PM
  #8  
Fork Horn
Thread Starter
 
Join Date: Dec 2003
Location: Wisconsin
Posts: 287
Default RE: Problem with Thomson center

Thanks for the help guys, I'll pass it on.

Cyber
cybersniper is offline  
Old 02-13-2004, 09:23 PM
  #9  
Giant Nontypical
 
C. Davis's Avatar
 
Join Date: Jul 2003
Location: Kountze, Texas
Posts: 5,050
Default RE: Problem with Thomson center

The Co2 discharger is for unloading your muzzleloader without having to fire your gun and dirty the barrel at the end of the day. I don't think most people who use one soak the breach in water before using it.
I have not used one, but I heard it is very effective, and it makes a distinctive "bloop" when it spits the dry charge and ball out of the barrel. As in 100% of the time, I would make sure the barrel is pointed in a safe direction (preferably a backstop) when using it.

C. Davis
C. Davis is offline  
Old 02-13-2004, 09:38 PM
  #10  
Spike
 
Join Date: Feb 2003
Location: Staples, MN USA
Posts: 76
Default RE: Problem with Thomson center

We have a TC Renegade and a Hawken. TC made special fittings to fit over the breach plug and remove them. It takes a pretty good wrench on some of them, but they are made to fit and do not damage to the plug. Have used them on both my Renegade and a couple of Hawkens. I am not sure if this item is still available, but they were back in the days I got mine.
vERN is offline  

Quick Reply: Problem with Thomson center


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.