cleaning
Whats the best stuff to clean a modern muzzle loader.
|
Depends on what powder you use. Triple 7: I use a citrus cleaner, Blackhorn 209: I use Hoppes solvent or any centerfire cleaner would work. Pyrodex/Blackpowder: use a cleaner designed for pyrodex/ blackpowder: water or citrus cleaner.
|
Real black powder, Pyrodex, Triple Seven, Alliant, and American Pioneer all clean up easily with a bit of ordinary dish soap and room temperature water. Any solvent for Blackhorn.
|
Semisane, I have found through a lot of trial and error that about the best soap for real black powder, I pretty much exclusively use Swiss, is that cheap Ajax dish soap. It seems to work the best of all of them. Dawn comes in a very close second. One little trick I ran across that makes barrel cleanup just a tad easier is to dry swab 2 or 3 strokes before you go to cleaning. Getting that layer of ash out beforehand seems to help a good little bit.
|
Originally Posted by hunters_life
(Post 4314814)
Semisane, I have found through a lot of trial and error that about the best soap for real black powder, I pretty much exclusively use Swiss, is that cheap Ajax dish soap. It seems to work the best of all of them. Dawn comes in a very close second. One little trick I ran across that makes barrel cleanup just a tad easier is to dry swab 2 or 3 strokes before you go to cleaning. Getting that layer of ash out beforehand seems to help a good little bit.
The two best products I could recommend are: Plain old Blue Windex and Then the final thing... a true synthetic bore oil - no petroleum - no Teflon or Slip 2000 |
If you want 1 product for all the ML powders take a look at Ballistol. You thin it with water for real black and most subs. Use it straight for BH209 and centerfires. It has the same main ingredient as Montanna Xtreme. Only the solvent base is slightly different. It uses a type of alcohol and MX uses a type of ether.
I do REALLY like the MX Bore Conditioner for short to mid length storage. IMO there are better rust preventers but if your bore is clean, dry then oiled rust wont be an issue anyway. As mentioned just avoid Teflon products IN the bore. They serve no purpose IN a bore. The only thing they can do is have a negative reaction to heat when fired. BTW a great product for drying a bore cleaned with water or to remove oils is non chlorinated brake cleaner. Just dont get it on plastics or the stock finish to be safe. It evaporates quickly taking the water/oil with it. It is rather toxic though so only use in extremely well ventilated areas. |
I've been using hoppes #9 for clean up with BH209 and I used it on another gun that shot Triple 7 FFFG. Should I be using something else?? Did I hurt anything using Hoppe's with Triple 7 powder??
|
Hoppes Elite (water based) is probably ok for Triple7 but not #9 which is a oil based solvent. Triple7 should be cleaned with a water based solvent or just some slightly soapy water. Windex with a drop or 2 of liquid soap and some isopropyl alcohol would be at the top of my list for Triple7.
A little 91% rubbing alcohol or ISO-HEET fuel line deicer will greatly speed up evaporation of the water and prevent it from freezing. ISO-HEET is nearly pure isopropyl and easily found at any place that sells automotive stuff. Even Walmart has it. Regular HEET is methanol and should be avoided or at least avoid skin contact as much as possible. |
Ahh crap.....I cleaned it with hoppes #9....
|
Originally Posted by zmason1002
(Post 4314887)
Ahh crap.....I cleaned it with hoppes #9....
|
All times are GMT -8. The time now is 01:35 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.