Duplexing Blackhorn209
10-08-2010, 09:40 AM
#93
Banned
Thread Starter
Join Date: Dec 2008
Location: Boncarbo,Colorado
Posts: 9,186
oh i have the proof to back it up, heck i even warned the person about getting some emails about me duplexing. He pretty much just chuckled and said, i know some have a problem with duplexing but they dont mind it when using pyrodex pellets or flash powder.
If that person was worried about the safety, he'd straight up tell me not to do it.
If that person was worried about the safety, he'd straight up tell me not to do it.
10-08-2010, 09:46 AM
#94
Banned
Thread Starter
Join Date: Dec 2008
Location: Boncarbo,Colorado
Posts: 9,186
received the followng email this morning., noticed it included a disclaimer.:
Chet,
Thank you for the e-mail. Yes, I did tell him it was OK. IN THIS CASE, this type of primer charge will not increase pressures or cause a negative effect. You might think of it as a kin to the black powder charge pressed in the bottom of a pyrodex pellet or even a flash pan powder that ignites the primary charge in a flint lock.
Thank you for the e-mail. Yes, I did tell him it was OK. IN THIS CASE, this type of primer charge will not increase pressures or cause a negative effect. You might think of it as a kin to the black powder charge pressed in the bottom of a pyrodex pellet or even a flash pan powder that ignites the primary charge in a flint lock.
Best regards,
Don Luhr
Western Powders
Ramshot/Accurate Powders
Tel: (406) 234-0422 email: [email protected]
Western Powders Inc -- Miles City – Montana.
Western Powders Inc. disclaims all possible liability for damages including, actual, incidental and consequential, resulting from usage of the information or advice contained in this message.
Use the data and advice at your own risk, and with extreme caution.
We also request that you visit our websites www.accuratepowder.com www.ramshot.com www.montanaxtreme.com or www.blackhorn209.com for more comprehensive information.
IMPORTANT NOTE: Always begin loading from the minimum "START charge and carefully develop loads by increasing in small increments of 2% towards the Maximum load.
Don Luhr
Western Powders
Ramshot/Accurate Powders
Tel: (406) 234-0422 email: [email protected]
Western Powders Inc -- Miles City – Montana.
Western Powders Inc. disclaims all possible liability for damages including, actual, incidental and consequential, resulting from usage of the information or advice contained in this message.
Use the data and advice at your own risk, and with extreme caution.
We also request that you visit our websites www.accuratepowder.com www.ramshot.com www.montanaxtreme.com or www.blackhorn209.com for more comprehensive information.
IMPORTANT NOTE: Always begin loading from the minimum "START charge and carefully develop loads by increasing in small increments of 2% towards the Maximum load.
If that isnt enough to satisfy the trolls i dunno what is.
10-08-2010, 09:47 AM
#95
Banned
Thread Starter
Join Date: Dec 2008
Location: Boncarbo,Colorado
Posts: 9,186
10-08-2010, 10:42 AM
#97
Boone & Crockett
Join Date: Apr 2007
Location: River Ridge, LA (Suburb of New Orleans)
Posts: 10,917
Well, since we seem to be working on the world's longest thread with 95 replies and 1,508 views so far, I thought I would add to it by posting reply #96 with a picture we can all agree on.
10-09-2010, 07:57 AM
#100
Nontypical Buck
Join Date: Jan 2008
Location:
Posts: 1,408
Edited: Forget it, after reading more of this thread I'm reminded why I don't bother with any board frequented by Grouse or SL anymore. Question is, is Grouse man enough to admit he was wrong and apologize? I doubt it.
Last edited by spaniel; 10-09-2010 at 08:13 AM.