Blackhorn Test Aborted - Mustang Down
BUMMER!
Most of you know that back in December I tried Blackhorn in the Mustang with the.25 ACP breechplug. I usedsmall rifle magnum primers and had delayed ignition on every shot and several failures to fire. After that shoot I ordered a new 209 breechplug from Lyman for a second try with Blackhorn. Well, that second try was today. I loaded the Mustang'sclean dry barrel with 105 grains of Blackhorn anda 300 grain Gold Dot in a Harvester short black sabot. I put aCCI 209 primer in the new breechplug andtook aim at a 100 yard target. When Igently squeezed the trigger the primer went POP but the gun didn't go BOOM.Dang! Put in another primer, pulled the trigger - POP/NO BANG. Dang! Dang! At this pointI'm getting "slightly agitated". I had thepan primer for my flintlock in the shooting box, so I used it to sifta little FFFg GOEXdown into the bottom of the primer hole, thenput a fresh209 in over the black powder. When I sat down at the bench again I was thinking "this GOEX boosted 209 is surely going to do the job". Squeezed the trigger. Click - NO POP. No POP? What the hell???? Opened the breech - no dimple on the primer. Closed the breech, pulled the trigger again. Click - NO POP. Opened the breech again, and stillno dimple on the primer. DANG!!!! The firing pin is broken.At this point my"slight agitation" turned into mild cussing session. Stuff happens, huh? What really bothers me is that those first two primers that did go off did not ignite the Blackhorn. I won't find out until I get the firing pin fixed, but it might be that the Mustang's breech plug just won't work with Blackhorn. I was sure gladI'dbrought along the Omega X7 and the .45 Renegade. So, instead of a afternoon with the Mustang and Blackhorn I gave those two fine riflesa littleworkout (report later). |
RE: Blackhorn Test Aborted - Mustang Down
man that sucks, sorry to hear that semi
|
RE: Blackhorn Test Aborted - Mustang Down
Well I am sad to hear that the Mustang broke down. Now we will get to see how well Lymans customer service is.
Glad you took a couple rifles so the day was not a total loss.. |
RE: Blackhorn Test Aborted - Mustang Down
Sorry for your loss
|
RE: Blackhorn Test Aborted - Mustang Down
Sorry ta hear about the broke pin:(
But your plug will need about a 1/8 inch flame channel, with at Least a .035 -.040 exit flash hole--that would be between about a #64-60 Numbered drill bit for the flash hole.:) Let us know how it goes after the repair;) |
RE: Blackhorn Test Aborted - Mustang Down
ORIGINAL: LaneNebraska Sorry ta hear about the broke pin:( But your plug will need about a 1/8 inch flame channel, with at Least a .035 -.040 exit flash hole--that would be between about a #64-60 Numbered drill bit for the flash hole.:) Let us know how it goes after the repair;) Does anyone see a problem with doing that? |
RE: Blackhorn Test Aborted - Mustang Down
ORIGINAL: Semisane ORIGINAL: LaneNebraska Sorry ta hear about the broke pin:( But your plug will need about a 1/8 inch flame channel, with at Least a .035 -.040 exit flash hole--that would be between about a #64-60 Numbered drill bit for the flash hole.:) Let us know how it goes after the repair;) Does anyone see a problem with doing that? I was referring to the 1/8 diameter of the flame channel not the length. Sorry for the confusion;) |
RE: Blackhorn Test Aborted - Mustang Down
ORIGINAL: LaneNebraska Semi I was referring to the 1/8 diameter of the flame channel not the length. Sorry for the confusion;) |
RE: Blackhorn Test Aborted - Mustang Down
spaniel
Andy, when they are talking about the 1/8" flash channel - they are talking abouth the channel directly under the primer that leads to the flash hole in the end of the BP. When shooting BH mine (flash channel) clogs up very quickly and the substance is very hard - kinda lke the worst 'crud ring' except in the BP instead of the bore. |
RE: Blackhorn Test Aborted - Mustang Down
Hey Sabotloader, in your plug how long is the .035 flash hole channel - measured from the end of the 1/8" flame channel to theface of the plug?
|
All times are GMT -8. The time now is 02:46 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.