@@Knight SuperDome Breech Plug-- BH209 Conversion!!@@
07-20-2008, 06:44 PM
#1
Typical Buck
Thread Starter
Join Date: Dec 2004
Location: Nebraska
Posts: 601
@@Knight SuperDome Breech Plug-- BH209 Conversion!!@@
Just figured this out! The SuperDome or the Part# 900043
http://www.knightrifles.com/productdetail.aspx?id=900043
Just get the drill bit that just fits inside the nipple mouth. Then drill out the nipple end towards the breech face, about 1 and 1/8 inches, or exactly 3 centimeters.
Do Not Drill Past the Breech Plug un-threaded, smooth shiny, Neck
Then you will have a BH209 ready breech plug, that lignite's every time
When you use NEW Red FPJ, there is no hang fires OR Blowback
Mine works perfectly! And allows me to use the Red Plastic Jackets if I want to!!! [8D][8D][8D]
.
http://www.knightrifles.com/productdetail.aspx?id=900043
Just get the drill bit that just fits inside the nipple mouth. Then drill out the nipple end towards the breech face, about 1 and 1/8 inches, or exactly 3 centimeters.
Do Not Drill Past the Breech Plug un-threaded, smooth shiny, Neck
Then you will have a BH209 ready breech plug, that lignite's every time
When you use NEW Red FPJ, there is no hang fires OR Blowback
Mine works perfectly! And allows me to use the Red Plastic Jackets if I want to!!! [8D][8D][8D]
.
07-20-2008, 08:32 PM
#3
Typical Buck
Thread Starter
Join Date: Dec 2004
Location: Nebraska
Posts: 601
RE: @@Knight SuperDome Breech Plug-- BH209 Conversion!!@@
[If it's the same Part# 900043 it sure will. I went to the Knight site and could not find any that said they were Specifically for the KRB[&:]
07-21-2008, 05:47 AM
#4
Nontypical Buck
Join Date: Feb 2003
Location: Kerrville, Tx. USA
Posts: 2,722
RE: @@Knight SuperDome Breech Plug-- BH209 Conversion!!@@
I shouldn't be the same part because the one for the KRB is set up to accept a 209 primer without the plastic jacket. But the powder end looks the same (domed) I think? Hard to tell for sure with that one picture.
07-21-2008, 06:22 AM
#5
Nontypical Buck
Join Date: Dec 2005
Location:
Posts: 3,246
RE: @@Knight SuperDome Breech Plug-- BH209 Conversion!!@@
ORIGINAL: LaneNebraska
Just figured this out! The SuperDome or the Part# 900043
http://www.knightrifles.com/productdetail.aspx?id=900043
Just get the drill bit that just fits inside the nipple mouth. Then drill out the nipple end towards the breech face, about 1 and 1/8 inches, or exactly 3 centimeters.
Do Not Drill Past the Breech Plug un-threaded, smooth shiny, Neck
Then you will have a BH209 ready breech plug, that lignite's every time
When you use NEW Red FPJ, there is no hang fires OR Blowback
Mine works perfectly! And allows me to use the Red Plastic Jackets if I want to!!! [8D][8D][8D]
.
Just figured this out! The SuperDome or the Part# 900043
http://www.knightrifles.com/productdetail.aspx?id=900043
Just get the drill bit that just fits inside the nipple mouth. Then drill out the nipple end towards the breech face, about 1 and 1/8 inches, or exactly 3 centimeters.
Do Not Drill Past the Breech Plug un-threaded, smooth shiny, Neck
Then you will have a BH209 ready breech plug, that lignite's every time
When you use NEW Red FPJ, there is no hang fires OR Blowback
Mine works perfectly! And allows me to use the Red Plastic Jackets if I want to!!! [8D][8D][8D]
.
Thank You,
Chap
07-21-2008, 06:44 PM
#7
Nontypical Buck
Join Date: Dec 2005
Location:
Posts: 3,246
RE: @@Knight SuperDome Breech Plug-- BH209 Conversion!!@@
ORIGINAL: txhunter58
I think that means Full plastic jacket? Never used one, so I am not sure.
I think that means Full plastic jacket? Never used one, so I am not sure.
Thanks Chap
